Recent content by Vincentsei

  1. V

    Incorrect magnetic heading/wind speed

    Why would it change during flight instantly on the same heading? Almost seems like what it was using for a mag var look up was wrong? When I started the aircraft for the next leg everything was fine, but as teh flight progressed same thing happened after about an hour and a half into the cross...
  2. V

    Incorrect magnetic heading/wind speed

    Back in April we had the GPS issue that caused the magnetic heading to be displayed incorrectly and cause windspeed and direction to be wrong. I installed the Beta software to correct the issue and flew the aircraft almost 20 hours with the issue resolved. I then installed the latest release...
  3. V

    Displays rebooting in flight USB data intermittent

    I just upgraded to the latest version 13.0.3 and flew two long cross countries. I have one 10 inch display and on one 7 inch. During both flights at about one hour into the flight the 10 inch display rebooted it's self. And the 10 minutes later the same thing happened on the 7 inch display. On...
  4. V

    CNX80/GNS480 waypoint not displayed on HSI

    First off thanks for the latests version of software it fixed most of the integration issues with us orphans who love our CNX80s/GNS480s. This restored the serial waypoints coming from the unit as well as problems with the ARINC data. but there seems to be one small problem with the ARINC...
  5. V

    Density Altitude Error on ADSB weather page

    I have noticed that every time I am flying to Albuquerque during the summer and go to check density altitude on the weather page provided by the ADSB reciever it is not correct. During the summer months the density altitude at ABQ is almost over 10,0000 feet, but the ADSB page is reporting...
  6. V

    No longer seeing nav data from gns480

    I have a 10 inch and a seven inch display installed and the auto pilot level and the serial GPS data are the only issues I have noticed. I have entered the set up pages on both displays and both are identical ( I have never just tried powering on o e display at at time to see what happens) The...
  7. V

    Level button cause climb then level off

    I have a tail dragger so the ADHRS is level to the plane. on the ground it is off by 5 degrees which is what I have the pitch bias set to so inflight the ADHRS is physically level. The other modes of the auto pilot seem to work. It will capture and hold an altitude fine frm a climb or descent...
  8. V

    Level button cause climb then level off

    I upgraded to version 10 and when I hit the auto pilot level button the aircraft pitches up to 5 degrees nose high then bunts over to level flight. I am below my max level flight air speed when I hit the button. I have tried letting it level off, and the disengaged the autopilot and hit the...
  9. V

    No longer seeing nav data from gns480

    Ok I set it to no and I still don't see nav data from my cnx80. It's configured as cnx80 serial 2. When I look at the message traffic the dynon is reporting messages received but has error and when you look at the data it's all 0000000. Worked fine in 7.1 but nothing in 10.
  10. V

    No longer seeing nav data from gns480

    I have maximum ap speed set at 183 knots and I was at 150 when I pressed level. The plane leveled the wings and started an aggressive climb. I have tried it now on three sorties and keep getting the same result. Any other ideas?
  11. V

    No longer seeing nav data from gns480

    Level button on autopilot cause aggressive climb I just upgraded to version 10 from 7.1 and have my auto pilot configured for expert mode. The autopilot was tuned and worked great in 7.1 but in 10 if I hit the level button in level flight the aircraft immediately does and aggressive nose up...
  12. V

    No longer seeing nav data from gns480

    I installed version 10 and I no longer see any nav data from my Apollo cnx80/garmin gns 480. I can edit the name for the GPS but the HSI only shows the name for the GPS but has dashes for distance and waypoint name. I have it configured as serial two and it is showing cnx80gns480 as the data...
Top