Recent content by ZK-LCM

  1. Z

    AUDIO ALERT WIRING

    Aaaahhh well life is never THAT simple. All was well when I just had the wiring "pigtailed" together. Then I got the wires properly spliced, and guess what, IT DOESNT BLOODY WELL WORK PROPERLY AGAIN. I am using the EFIS audio output as the input to my ICOM aux. I can't get any EMS or AP...
  2. Z

    D120 EMS Tacho Setup

    Folks, I have gotten my D120 EMS Tacho readings to agree with a strobe tacho and be correct on either mag. My configuration is a Slick impulse Mag on the LH side of my 0-320-D1A, and an LSE Plasma II mag on the RHS. I have noted some confusion over the settings for some installations, so FWIW...
  3. Z

    AUDIO ALERT WIRING

    Hopefully the installation is now completed. Though we haven't flown yet. Here is what I ended up doing. 1. I did not put my aural warnings, (from the EFIS only), thru a potentiometer, instead I adjusted the ICOM aux input volume internally. 2. On Dynon's recommendation I disconnected my...
  4. Z

    AUDIO ALERT WIRING

    I suspect my problem is due to my Pitot Heat warning light being wired into my D120 EMS, which is permitted by the instn Manual. And of course, all of the Dynon items talk to each other via the ADSB. I shall ask Dynon directly.
  5. Z

    AUDIO ALERT WIRING

    I do NOT have a Skyview. My installation consists of a D100, D120, AP74 and a Dynon Heated Pitot/AOA system. So the AOA data comes from the Dynon Pitot/AOA.
  6. Z

    AUDIO ALERT WIRING

    Well, most of the audio alerts work OK & the Test functions all work. BUT My AOA voice and tone warnings all come on, even when I set a Min speed, and my AOA symbol shows a solid Red alert. That in itself is strange, but what follows is even stranger. When I turn on Pitot Heat my warnings...
  7. Z

    AUDIO ALERT WIRING

    If anybody wants more detailed instructions, I shall ATTEMPT to provide them.
  8. Z

    AUDIO ALERT WIRING

    Ahh well, progress at last today, after frustratingly trying every combo of outputs & wiring. It transpires that I had to delve into my ICOM IC-A210 Comms menus to setup the auxiliary inputs. You can turn them off (why would you?), ON, & adjust input volume. So now I get audio alerts. There...
  9. Z

    AUDIO ALERT WIRING

    Thanks everybody. Interestingly Dynon advise me that I must use only one pot and put only one audio alert input into it. So tomorrow I shall try just my EFIS audio output into the pot. Of course, the components all talk to each other thru the DSAB.
  10. Z

    AUDIO ALERT WIRING

    Folks, My installation consists of a D-100 EFIS, D-120 EMS, & Autopilot which includes an AP-74. One ICOM Comms VHF radio. Day VFR Operations. The wiring instructions for Audio alerts, (To an intercom), require the audio signal to connect to the Intercom via a 10kohm potentiometer. My question...
  11. Z

    AP Servo Push Rod misalignment.

    Thank you for the excellent & prompt reply. Is it possible to obtain a copy of the Rod End spec sheet?? Thanks
  12. Z

    AP Servo Push Rod misalignment.

    I am nearly finished my RV6 which has a D100, D120 & a Dynon Autopilot . This has been a very slow project, way down in new Zealand, & I installed the Dynon AP hardware approx. 6 years ago to Dynon document 101046-001 Rev D. Page 7 of said document specifies that the Aileron servo is 5.875" aft...
  13. Z

    Dynon Pitot/AOA probe protection

    Folks, This may be the wrong forum for this subject, but I cant find a specific forum for the Dynon Pitot/AOA system. My question is whether users have found a suitable Pitot cover for this Pitot head, and if so where is it sourced from, & what make/model is it.  I see that AC Spruce sell a...
  14. Z

    Flowmeter wiring Plugs

    Folks, I am wiring my FT-60 Red Cube flowmeter to my D120 EMS (0-320 RV6). I purchased my Dynon kit about 10 years ago & the terminals Dynon supplied have gotten mixed up with others. The only plugs that I have that mate fully with the plugs on the red cube are Vans ES421-0107 (male) &...
Top