Search results

Yeah I replaced the wiring harness in the avionics bay where the 4 wires split on their way to the 2 x HDX screens... No fix. Ended up being a faulty 4 pin connector tin the tail near the GPS module.

Hi all, I have an intermittent issue whereby I lose position data from the GPS-2020. I can't tell if it's a signal data issue or power to the module issue. Maybe the following info will help. CAUTION: POSITION SOURCE 1 FAIL NO ADS-B OUT: GPS LOST ON MAP: POSITION UNKNOWN TRAFFIC FAIL 2 x...

Second this ^^^^^ What I did as well with my 7A

Ok thanks guys I'll check to see if it's in EM. Another thought, does Obstacles data have to be current. Only NAVDATA is current ATM. It's probably just me not knowing how to load and configure the VNAV but all approaches are listed as RNAV in the menu rather than RNP, which is the title of the...

So the auto-pilot will physically fly the vertical profile?

Hi Guys, So I'm running a full Dynon HDX suite with ARINC429 incorporating a Garmin 175 WAAS Navigator. I'm happy that I can use it fly RNAV approaches with lateral guidance, but can it also provide vertical guidance? Or is this only available if it is fed with BARO data? I've loaded the...

Hi guys, Can someone please confirm if I need two Wi-Fi adapters for the Wi-Fi to work (dual HDX setup) or if a single Wi-Fi adapter plugged into the primary HDX is sufficient??? This is what it states in the setup: "OFFLINE: NO ADAPTER OTHER SCREEN". I was of the impression that I could...

I'm having issues as well. When I power down the system (Master Off) with the Skyview backup battery taking the load it then acts as it should, asking if I won't it to remain ON, Power Down or Test Battery. Issue being that the 'Test Battery' selection is grey rather than solid black. How do I...

Update: Found a short between inner and outer coax. I'll fix that and report back

Sorry, to add.... I've checked the antenna pins at both ends and the D25 that slots into the back of the SV-INTERCOM-2S. All seems to be fine. What other testing can I do?

Hi all, I have a single SV-COM-X83. It seems to be receiving well enough (I think), but Tower always struggles to hear my transmissions. Installed in an RV-7A, under tail mounted antenna. Ready for first flight once this is sorted. Thanks, Dan

Thanks guys. Yes I've set the IAS tape colours but may need to focus on calibrating the ADAHRS first. Will advise...

Hi Dynon, Wiring is correct and both servos are on the network with up to date firmware (16.4.0.9609). Why does status state 'not installed' when attempting to run the calibration? Must the ADAHRS compass be calibrated first? Any other ideas? Thanks, Dan

It seems to have disappeared but I’ll keep an eye on it. Thank you

Good idea. Thanks Albee. Unfortunately this won’t be as easy for me as I’ll need to switch pins on the D37 connector… such a PITA to pull everything apart. It might be best for me to stop messing with everything and send it back for the specialists to test. I’m worried that if I continue to...

Thanks Dynon, I know the wiring is correct. Something is not right with this module. Can you assist with a replacement or do I need to work this through my supplier?

For some unknown reason this error has now disappeared. WTF

Hi all, I've installed a SV-GPS2-2020 and I'm concerned it's faulty. I've double-checked the wiring and serial configuration. There is no data traveling between the GPS and the SV EFIS. Other than testing the wiring for power, continuity, correct pin assignement and configuration, is there...

Hi all, I've got a No SV error on the comm panel and I can't transfer frequencies from the SV to the comm. What have I done wrong? Thanks, Dan +61 0404 869 261 Australia

Was not..... not, was was