Search results

A Wow! from me too! I like all these updates in the software. Last week I flew to Oshkosh and back and my Skyview functioned flawlessly. I appreciated all the functionality I have and to see more coming is impressive. I did invest in a back-up with I Fly GPS for my Iphone or Ipad and their rep...

Has there been any interest in an auto-zoom feature. It would have a setting when you got with a set distance from your waypoint the map screen would begin to auto-zoom making your approaching area more detail. This would be something which could be turn on or off. Any interest or requests before?

I was watching a video associated with map usage on Skyview. The instructor talked about turning OFF the Terrain Proximity Alert function. Where is this function located, which menu? Thanks in advance for the direction.

Well I must be close. The Skyview map does not auto zoom, or at least yet.

I may be missing this somewhere in the set-up but I was trying to get my Map system to auto-zoom as I got closer to the entered waypoint. Say I have my map set on 12 miles and once I got closer than 12 to the waypoint the map would get closer/more detail as I approached the airport. Is there...

I too am having a similar issue. I am flying an RV12 with the Skyview. I have read some other posts where an adjustment guide is referred to. Is this in the operator guide?

I too have an RV12 and need to know how to get to the screen where the K factor/pulses can be adjusted with my Skyview.

I could see the changes in voltage associated with adding fuel and progressing through the prompts. There was an arrow at the bottom and I was unsure how to see the values. I turned knobs and nothing and I didn't want to push anything which would cause me to loose the data. So I will try edit to...

There is an earlier screen shot of the calibration results with the point, volts, and value. How do you get this to move? I see the arrow at the bottom, but can not view the other points.

I received a suggestion from another RV12 guy who mentioned whether the AP had been on during the last software update and I was pretty sure in had not. So I turned on the AP and Avionics then started the Skyview. I saw in the center of the screen where updating to the servos were occurring and...

I had started into a similar situation with the calibration and received an ERR message on the first attempt in my RV12. Now I can not getting it to move to either re-calibrate or fix the ERR. The installation manual did not have any information about how to proceed. I saw another post about a...

Thanks.

I am doing the installation of my Rotax engine in an RV12 and have the Skyview package offered by Vans in route. One of the many things I have been reading about others experiences is with the fuel pressure sender. I was shipped a round barrel looking sender orginally used with the D180 system...

Thanks for the direction to the pages with the instructions I needed to navigate the latest firmware changes. I switched to the "modern" screen option. It was fun to figure out all the different screen options and displays. After a couple of trials with different displays I think I'm set for...

After installing 3.0.0 my time looked hay-wire too. It showed a time spread that didn't appear correct, I will check it again. How do you switch from traditional view to the new view? I saw something in the site text about going to the set-up, and that is where it can be switched. My D100 is...

Today was one of those days, the ones where the sky was hazy and stable, and when I got up there was little to no wind. Everything matched up within 1 degree so I think everything is pretty close to set as good as it's going to be. My next step is to install the new firmware and see how that...

Thanks for the advice!! In fact one of the guys in the hangar across the row offered him whiskey compass to take up and use for varification.  I will cautious of the electrical fields, and be not so trusting of the readings received. I will also use the section lines to try and see what those...

I came to the site tonight to comment on my compass, the readings I am getting, and and the location the magnetometer location. Mine is mounted in the tail area under the empenage fairing. There are a few steel bolts in this area, but the area is mostly aluminum. A fellow pilot installed his...

Just wanted to confirm that, and as usual !!! YOU GUYS ARE THE GREATEST!

Sorry for any confusion. My original question is simply -- Will the new format and upgraded firmware download to my existing D100, or is this for just all new units after sun-n-fun? :-?