Search results

  1. R

    Canopy switch rpm rpm enabled

    Never got this feature working, if someone would like to help trouble shoot what I've got wrong.
  2. R

    Servo Torque

    Thanks, I must be getting a small slip as I have never felt it. I have not adjusted any of the settings, should I look into the settings to help or are they not related to the slip condition?
  3. R

    Servo Torque

    I'm getting slip messages every once and a while but never experienced loss of autopilot control. Why it this happening?
  4. R

    Canopy switch rpm rpm enabled

    Still working on my install. Finally got my widget in place and I'm using contact pin #23 so I can use the 12 V. I already have going to the canopy switch for the dash mounted indicator light. In my case it appears that pin # 23 needs to go to ground to change the widget from open to closed. I...
  5. R

    Canopy switch rpm rpm enabled

    I think I have succeeded? Thanks a bunch. Ron
  6. R

    Canopy switch rpm rpm enabled

    Thank you very much planecurious. My problem is still that my computer will not allow me to open the file. I tried to download a couple programs (if that is the correct term) to down load the file for viewing with no luck. The just for trial programs say you need to purchase the program to view...
  7. R

    Canopy switch rpm rpm enabled

    I guess I have it saved but I cannot open it. Maybe it's not a file that you open , maybe I need to load it onto a stick and load it into my Dynon. I work with hammers and wrenches not computers. Anyone need help with a hammer?
  8. R

    Canopy switch rpm rpm enabled

    Trying to down load this file but no luck. Any suggestions
  9. R

    8 lower button changing

    I'll keep an eye on it and disable it if it becomes a problem. I might also have a problem with my only back up battery. I would think with 40 hrs. on the aircraft the BU battery would have been fully charged, but I tried once again to do the test required and found the battery at only 11.6 V...
  10. R

    8 lower button changing

    Hello Support Ran the touch test and failed every try on the first step. Failure due to not starting on the green dot message displayed. Tried the same test on the pilot display and passed all seven steps. I purchased these units from ACS in Feb. 2015 and with a little flying weather left yet I...
  11. R

    8 lower button changing

    Thanks, I'll give that a try. Ron
  12. R

    8 lower button changing

    Not too techie here, but here goes. On last flight my co-pilot's 10 inch touch display would every once and a while change the functions of the 8 lower buttons all by it's self. It would go from the autopilot function showing to the lean function showing all by itself with no input from me (or...
  13. R

    EMS information on secondary display not working

    I left a message with tech support (phone) two days ago on this issue and am still awaiting a return call. I also called and spoke with Kelly (I think that was the nice lady's name) again yesterday and she said there was only one tech answering calls and he's very busy trying to keep up. thanks Ron
  14. R

    EMS information on secondary display not working

    I have two 10" touch Skyviews in my not flown RV-14A. Until about a week ago the two screens functioned as I expected, showing the engine parameters on both screens. Lately the co-pilot side has x's across most engine widgets. The message shown indicates " EMS SFG mis match". I downloaded the...
  15. R

    796 audio alerts

    Another question, can we connect more than one device to pin 17? I have the 796, and would like to add a Co-Guardian CO detector, tone and Van's Stall warning tone. Any chance we can just connect all three wires to pin 17?
  16. R

    796 audio alerts

    Called Garmin and was told to only connect one or the other, Left or Right, not both connected together. In case someone else needs this information. Thanks again Ron
  17. R

    796 audio alerts

    Thank you very much, I will do that . Ron
  18. R

    796 audio alerts

    I would like to hear the audio alerts from my 796 thru the SV-intercom to my headsets . I'm using the Garmin bare wire harness. Can someone tell me which of these wires connect to the SV-Intercom and to which pin. The SV-intercom is not stereo so do I connect left and right together. I would...
  19. R

    RV10 Autopilot Servo

    Just replaced the servos on a flying RV-10, no big deal. Unscrewed the mount, replaced with the new the mount and mounted the SV-42T and rewired. Getting back there was the hardest part, but luckly I'm small. Ron
Top