Search results

  1. J

    Lightspeed III Ignition Advance on Skyview

    Been studying and have more questions. I copied this segment from the voltage segment for C37, Pins 1 & 2 All I did was to change the id, pins, names, and min – max values. Do I just add this in line in the existing sensor config file? Will the following code, lines, instructions, whatever...
  2. J

    Lightspeed III Ignition Advance on Skyview

    I'm having trouble with this also. I'm using a Lightspeed L2e signal box to send timing info from both Lightspeed boxes to the Skyview EMS. I'm using EMS pins 22 & 23 configured as pressure with the 0-80 psi selection. The output from the signal box is 0.1v per degree of advance. 2.5v = 25...
  3. J

    ADSB 472

    I assume that those of us on the waiting list for a 472 are now on hold until this is resolved. I'm also using an AAE - L2 antenna and receiving fine with my 470.
  4. J

    Videos for Autopilot Vertical Modes??

    Thanks, haven't seen that one.
  5. J

    Integral IFR GPS navigator

    If the past is any indication, they could say no plans today, and announce it tomorrow. I'm just hoping for tomorrow!
  6. J

    Integral IFR GPS navigator

    I think it is great that Skyview will be showing up in some certified aircraft. I think Dynon is missing the boat big time not having an integral IFR GPS navigator. It has to be coming!
  7. J

    Videos for Autopilot Vertical Modes??

    Are there any videos for the Skyview advanced autopilot vertical modes? I haven't found any. Would like to see some!
  8. J

    Trying to free up a serial port

    OK, I can use the GPS output of my Garmin 396 for the ELT so what I really need is info on using my GPS2020s one at a time and what must be switched. The question is, will it hurt a GPS2020 if it has power and ground but the TX & RX are open? I either need a -- 2 pole, 2 throw or 4 pole, 2 throw
  9. J

    Trying to free up a serial port

    ADSB - - - - - - - - -Port 3 PFD & MFD Transponder 261 - - Port 1 PFD & MFD VPX - - - - - - - - - - Port 4 PFD & MFD GPS 2020 #1 - - - - -Port 5 PFD & Port 2 MFD GPS 2020 #2 - - - - -Port 5 MFD ACK ELT E-04 - - - - -Port 2 PDF The ports are already overused as the #2 GPS2020 only inputs to...
  10. J

    Trying to free up a serial port

    Can I put a selector switch to choose which GPS2020 I want to send to both screens? 4 pole, single throw? What about 2 pole, single throw and just switch the TX & RX? With everything powered up would there be any induced problem(s) from switching between the GPS sensors. I currently have...
  11. J

    Can AOA widget be moved and size changed?

    That is a shame. For me, it is too low and too small to be anything other than a toy. :-[ Also, having the AOA audio as a percentage of the total audio volume is problematic. If the total audio level is set to comfortable levels, the AOA, which should be intrusive like a stall warning, is...
  12. J

    Can AOA widget be moved and size changed?

    Can AOA widget be moved and size changed? Skyview Classic
  13. J

    RAIM

    What would be required to add RAIM to the Skyview system?
  14. J

    AOA calibration and full power stalls.

    I did the same as Carl with the same results in my Sportsman. I wanted to just hear the start of the beeping as I slow down on final so I recalibrated with no flaps. It is just a bit too high so I will try recalibrating at first notch. Setting the AOA seems to be a process, not an event.
  15. J

    Checklist Request

    1. I really like the checklists. It helps me. :) 2. I would really like to be able to scroll down through the items on each checklist to show a highlight background, a color change, an arrow, or anything as I perform the checklist. 3. Then I would super really like the checklists! :D
  16. J

    Replaced Transponder, Lost Auto-Pilot

    New day, fresh eyes, and found that somehow the change of transponder had somehow driven a requirement to re-calibrate the autopilot servos. Calibration performed and system operational now.
  17. J

    Replaced Transponder, Lost Auto-Pilot

    Additional information: Network Status shows both servos as available. Autopilot Setup Menu (SETUP MENU > AUTOPILOT SETUP) is grey and not available.
  18. J

    Replaced Transponder, Lost Auto-Pilot

    My Skyview is not even recognizing my installed and previously working servos.  I don't get any Auto-Pilot legends above the buttons on the SV. I have no Transponder or Auto-Pilot warnings. My transponder firmware is on-line HW22.03 FW01.02 SW02.09. I'm getting .02 amp readings for the servos...
  19. J

    Seattle charts issue, anyone seen this?

    I talked to Seattle Avionics about the issue and they had the solution for me. In my power saver mode I had set the laptop to go to sleep after a time of no use.  It was going to sleep while downloading the info and corrupting the files. I reset my laptop so it never goes to sleep while...
Top