Search results

  1. A

    AOA Indicator constantly appears

    Is recalibrating pretty easy?
  2. A

    AOA Indicator constantly appears

    Ok, so when looking at photo #2 you will notice that the AOA indicator isn't all the way full and indicates it's moving towards a reaching the critical angle of attack. What would cause it to display this while level on a taxiway? I can see how since I have an IAS of 20 some knots that the AOA...
  3. A

    AOA Indicator constantly appears

    It was EXTREMELY gusty that day. Where can I go in the settings to check this menu? I had a wing that bumped a hangar door but I am doubting that this happened due to that.
  4. A

    AOA Indicator constantly appears

    Could you elaborate a bit more? Can I adjust this easily to test the theory? If I understand right your saying that any time if have an IAS it will display the meter? Thus why on a 21IAS taxi it displayed it? Can I test this by just seeing if it displays while sitting in the hangar going nowhere?
  5. A

    AOA Indicator constantly appears

    So I noticed the other day when taxi on the ramp that my AOA indicator was displaying on the Dynon Skyview display. Typically I do not see this until I break enough of an angle to get it to pop up. I've had no changes in the aircraft, is there any reason this is now displaying. The first photo...
  6. A

    Updated GPS Fix lost ADSB....

    You don't have to respond if you don't like? I saw that section in the manual, but after reading it still don't understand if that means that was the problem. All of that is still a bit confusing for me. I understand what it's saying but I still don't understand if that is the reason I didn't...
  7. A

    Updated GPS Fix lost ADSB....

    Matter of fact, look in the photos my XPNDR is set to 1200 ALT ... could that be the cause?
  8. A

    Updated GPS Fix lost ADSB....

    Do I have to be seen on the ground for it to pass the mandate or just the air? Theres a good chance my transponder was still in ALT from my flight last week, I don't think it defaults back to ground when I land. Could this cause it?
  9. A

    Updated GPS Fix lost ADSB....

    And I ran the FAA site earlier and it failed
  10. A

    Updated GPS Fix lost ADSB....

    I assume the below photo is the page you are speaking of?
  11. A

    Updated GPS Fix lost ADSB....

    I am not sure what this is, I went back this morning to the hangar pulled the plane out and started it up. I checked my GPS screen and had all green and I think 10 connection points on the GPS. I went into the ADS-B Status screen and this time instead of STATUS:NOT FOUND. I had STATUS: NO...
  12. A

    Updated GPS Fix lost ADSB....

    So I had a message that the software version of one or more of my SV-GPS-2020 devices installed was out of date and was told to enter the GPS FIX STATUS menu and press load to begin the update process. I pulled the plane out of the hangar and ran and successfully completed the update. When done...
  13. A

    New Dynon screen went all white!

    These guys are absolutely AMAZING. I've never had a company take so much time to walk me through issues. Thanks Don!
  14. A

    New Dynon screen went all white!

    All good, you guys sent me a second screen and all seems to be fine so far.
  15. A

    New Dynon screen went all white!

    I looked in log and don't see anything...
  16. A

    New Dynon screen went all white!

    Did a reset w/ buttons 1 2 & 5 and it cleared, any ideas what may have triggered it?
  17. A

    New Dynon screen went all white!

    So I had my Skyview screen sent back to Dynon to get repaired as the top half was going faint. They repaired some wires and put in a new screen. I had it installed the other day, flew for an hour or so. Went out tonight for a few hours and right as I was coming in to land for the evening the...
  18. A

    INDENTing Issue

    So when I normally fly I hit "VFR" and it goes to a 1200 squawk. I only IDENT usually when asked to by ATC, and then I just press IDENT. Is the correct process to press just "ALT" to IDENT ALT? or is it IDENT then ALT? Thanks
  19. A

    INDENTing Issue

    So yesterday on my way back to my Airport ATC asked me to IDENT given the excess traffic due to one of our local airports being closed down for students due to a NFL Notam. Anyways, I kept just hitting IDENT on my D100 Skyview it would show IDENT and a # for a bit, then go back to that # with...
  20. A

    Audible Airspace Warning

    Ingenious! Ty
Top