Recent content by andresmith76

ve0kog - How did you get your pitot heat widget to work? I can't get my Dynon pitot to correctly indicate (always indicates ON) and working with Dynon tech support, was told they couldn't either.

As of this morning, I can verify Seattle Avionics has updated the Chart Data. So much for AI . . . "Shall we play a game???"

Exactly - and Dynon allows you to go into the Settings menu and enter those 3 parameters numbers as you want. What I'm wishing for is Skyview to capture and record the airspeed where each stall occurs for future reference. Doing so would be more accurate than me having to watch and remember the...

Rhino - being an experimental, my POH is what I make of it. If the other V speeds, which can change, are indicated - why would including stall speeds be wrong?

I just completed the stall/AOA calibrations for the 4 different flap settings on my RV-14A. I was surprised to then find out Skyview doesn't record or display the airspeed where each stall occurred. I wish Skyview would indicate the stall airspeed values for each flap setting (Vs, Vs1, Vs2...

I also have the OLED COM radio with the same dim, non-adjustable brightness display. I spoke to a Dynon tech that said they were aware of this and an adjustable brightness feature will be included in the next software release. No specific time frame was given on when the update will become...

By chance, have you downloaded and read Dynon's Third Party Connection and Configuration Guide: https://www.dynonavionics.com/skyview-documentation.php Pages 6 & 7 show the proper interconnect wiring between the GTN6XX/7XX & ARINC-429 module, GTN Configuration settings and the Skyview Setup...

No. As the software upgrade was what caused the unit to fail, Dynon replaced the defective module at no charge.

I had an HDX ADAHRS-200 fail after I upgraded the system software last year from 16.7.0 to 17.0. Dynon tech support helped me roll back the software to 16.7 but that did not remove the big red X from the display. I eventually had to replace the unit with a refurbished one to get my system...

I added this request to the "Skyview Wish List" thread back in Aug. 21, 2021 (3rd post from top): https://forum.flydynon.com/threads/skyview-wish-list.12851/page-3

I didn't build my RV-6 but it does have the magnetometer mounted in the tail section as shown. Note the nylon mounting hardware. You are correct - mounting in this location keeps it away and clear from magnetic interference caused by antennas, other equipment, etc.

An update - I spoke to David w/Dynon Tech support and he did confirm that each CDI deviation marker did seem to indicate 3 1/3° when receiving VOR signals. I asked why Dynon would choose a non-industry standard of each marker representing 2° and he wasn't sure. He did say he would mention this...

My Dynon Touch CDI shows 2 dots to the left & right of each wing tip on the centered plane symbol (Pilots User Guide, figure 23, page 4-13). "When in NAV mode, full scale deflection indicates ten degrees of deviation from the VOR radial" (page 4-15). On other CDI's, I've seen 5 dots/marks to the...

Yes. As far as Skyview is concerned, the Dynon radio is the only one it knows about, controls and displays. I need to select COM1 on the 240 to listen to the 650's radio. Regardless of how the 240 is configured, Skyview's top bar display only shows the frequencies entered on the Dynon radio...

In my 14A's panel, there are 2 ea. Dynon Skyview Touch screens, a GTN-650 & a GMA-240 audio panel - all wired by Stein Air - and this is how the system is connected. The GTN-650 connects to the Dynon Skyview network through the Skyview ARINC-429 module. The GTN communicates/supplies data to the...