Recent content by WEdgar

  1. W

    Battery Connector

    What is the part number and description of the Connector for the D10A BACKUP battery; both male and female connectors- THANKS
  2. W

    Dual D10As

    Appreciate your guidance. To be clear, for this discussion and for anyone else that may be interested, by connecting at the back of each D10A the #4 pins together and the #5 pins together with a shielded twisted pair wire, that both D10As will be capable of displaying the same information...
  3. W

    Dual D10As

    Thanks for the comment. There is no network. There are two D10As. There is one GpsAntenna. There is one RemoteCompass. There is one TemperatureSensor. THAT'S IT !!!! THE QUESTION: "Is there a correct wire diagram for connecting two D10As to a single GpsAntenna and single RemoteCompass and...
  4. W

    Dual D10As

    Is there a correct wire diagram for connecting two D10As to a single GpsAntenna and single RemoteCompass and single TemperatureSensor -please advise.
  5. W

    D10A Voltage

    Ye it's an answer, but not an accurate answer to the actual question. Maybe you could help, I see you have a D10(is it a D10A), is your system 28v; if so what voltage reading does your unit display in cruise, kindly specify in 10ths (ie: 28.2 28.6 etc.). For some reason the D10A will display...
  6. W

    D10A Voltage

    The future of aviation instruments is with electronic instruments; but this requires some integrity. The following request has been made numerous times: ""Kindly provide the D10A voltage reading when the power supply is specifically set at (each of) the following values: 28.0; 28.1; 28.2...
  7. W

    D10A Voltage

    Is there a reason the previously requested has not been conducted: "Kindly provide the D10A voltage reading when the power supply is specifically set at (each of) the following values: 28.0; 28.1; 28.2; 28.3; 28.4; 28.5; 28.6; 28.7; 28.8." THANKS
  8. W

    D10A Voltage

    The comparable wire lengths are within a couple of inches, that would not provide a significant variation. Kindly provide the D10A voltage reading when the power supply is specifically set at the following values: 28.0; 28.1; 28.2; 28.3; 28.4; 28.5; 28.6; 28.7; 28.8. THANKS
  9. W

    D10A Voltage

    Is Dynon abandoning support for the D10A or just busy; this voltage question has been setting on the forum for over a week, I'd sure appreciate a correct tested response.
  10. W

    D10A Voltage

    Did you connect the D10A to a power supply and verify that voltage range of 10-30v including 10ths. ? D10A will display voltages correctly in 10th at 24.4 volts; but when the voltage increases to 28.4 or 28.6 the D10A displays 28.0. Please verify what the D10A displays when power supply is...
  11. W

    D10A Voltage

    What is the maximum Voltage the D10A will accurately display on a 28 Volt system
  12. W

    D10A Glide Slope

    The problem is when Cdi+GS is selected, the CDI appears correctly but the GS does not appear at all, nothing. I'm assuming there is a setting somewhere in the D10A that is blocking the GS display I just can not find anything in the documents to answer this issue.
  13. W

    D10A Glide Slope

    The D10A Cdi is working correctly but the GlideSlope is completely missing from the display screen. What is needed to display the Glide Slope ???
  14. W

    D10A Altitude Error

    "The software responds nearly instantly, so you wouldn't see that amount of lag from the EFIS itself." How much lag would you expect to see in feet? "If, when you're level" How long are you intending on being level? "your EFIS matches your barometric altimeter" I would expect this should...
  15. W

    D10A Altitude Error

    Lags a certified altimeter and waas Garmin430 and ATC radar
See more
Top