Search results

  1. A

    Message Alert ... XPNDR FAIL

    RV7 built in 2012. Installed the Garmin GTX 327. Was flying the other day message alert came up XPNDR FAIL. Called ATC and they told me they could still see me. Msg still there on a number of flts. Slid the GTX out from the case and reinstalled it. No joy. Anybody have any ideas on where to go...
  2. A

    Dynon Unheated AOA/Pitot Probe Installation

    I have a RV7 quick build that i have been flying for 5 yrs. I installed a inexpensive stainless steel pitot tube during the build. I now want to install the unheated AOA/Pitot Probe. Is it possible to install this with a finished wing?
  3. A

    Zoom In/Out Buttons

    Hi Dynon, Has the bug on the Zoom In and Out Buttons ever get fixed. I am running software 13.0.3. http://dynonavionics.com/cgi-bin/yabb2/YaBB.pl?num=1433713943/0#0
  4. A

    SV Airspeed Tape Issue

    I was flying with a friend on his RV7A. I noticed on his GRT EFIS speed tape that on approach you could see the tape was red below his stall speed. On taxi in the numbers were also in red. I am not getting that feature on my Dynon SV. I only see white on my airspeed tape at low speeds. I see...
  5. A

    Skyview/Garmin GTX327 Issue

    There is lots of history on this issue. Have been working a long time to solve it. I want my GTX327 to start-up in Stby mode, then transition to Alt mode on T/O. On LDG to transition from ALT to Stby. SV Serial Port 1 RX is connected to pin20 on the GTX RS-232. SV Serial Port 1 TX is connected...
  6. A

    HSI+ALT window Issue

    When Map Panning Mode Pointer is moved to a place and Direct To is selected, the magenta line extends to the place that I selected. The Info Page appears showing the place that I selected. I select Navigate and DTK+Dist+ETE appear showing numbers that correspond to the place that I selected. It...
  7. A

    Widgets

    Deleted elev trim and flaps on the Eng. full screen page. When i selected split sceen, both widgets were showing in light grey. Went into sensor input mapping and deleted flaps and that solved the problem with widget on split screen. I then deleted elevator in sensor input mapping. When i went...
  8. A

    Light Speed Plasma II conection to SV (no pins)

    I have a left mag and a right LSE plasma II. I am using the June manual 6.0 release page 7-32 fig 29. I need pin 32 white/geen for my L mag connection and pin 35 green for my lightspeed connection. When i look at my DB37 connector cable there are no female barrel pins in slots 32 to 35. There...
  9. A

    Skyview powers up intermittently

    Skyview in garage. RV7 not completed. Have been powering up Skyview many times before. All of a sudden it won't power up. Turn Master Switch off then on and it powers up. Somtimes it doesn't. You have to turn switch off then on a couple of times before it powers up. Battery Voltage 12.3
  10. A

    Top bar on Skyview will not show Squawk Code

    GTX327 Transponder.  Dynon pin 3 (Serial Port 1 RX) to GTX pin 20 (RS-232 Out). Dynon pin 4(Serial Port 1 TX) to GTX pin 19 (RS-232 In) Dynon pin 6 (Serial Port 2 TX) to GTX pin 2 (RS-232 In) Skyview serial ports 1 and 2 confiigured for ICARUS as per Example SV Serial Port Config on page 4-15...
  11. A

    AvMap EKP-4 Interface to Skyview

    The EKP-4 Serial Cable has a single pin connector on one end and a 9 pin connector on the other. The single pin conector is plugged into the EKP-4. On the connector end,(EKP4) i have connected pin 4 of EKP4 to DB37 pin 3 Brn with Orange stripe - Serial Port 1 RX. Pin 3 of EKP4 to DB37 pin 4 Brn...
  12. A

    SV-ADAHRS-200 Red Blinking Light

    Just hooked up the ADAHRS to the Skyview. Skyview is not seeing ADAHRS. Am getting a red blinking light on the ADAHRS unit. Anybody know what this about?
Top