Search results

My non dynon wifi adapters have been working well for in my dual screen set up for over 300 hours. It now seems one has died. The same model is no longer available and so I am wondering if anyone has a non dynon wifi adapter install and what the make and model of that wifi adapter is. Thanks

They are in the serial cable, DB9 connectors.

FWIW I installed a panel mounted toggle switch which can disconnect power to the servos. I thought in the event of an emergency flicking the switch would be preferable to pulling breakers or switching things off in the VPX. I labelled it 'AP master'. Usually it just stays in the on position.

I reported this to Dynon shortly after the latest release. They have referred the matter to engineering.

I have had a few sensor failures on my D1000 classic. The characteristics of the failures were exactly the same as you describe. In the end I suspect poor connections from the EMS harness to the EGT sensor wire were the problem all along. Obviously I couldn't prove it as the other sensors were...

Yes I have 2 x D1000's and they both have the backup batteries, and both are regularly tested.

The issue has not reappeared since. I also replaced my battery, though I don't see how that could be a source of the issue.

On my installation the supplied harness wires were long enough to reach everything they needed to. The EGT and CHT wires already had connectors attached to connect to those coming from the EGT and CHT sensors supplied. On other sensor wires like oil and fuel pressure I attached appropriate...

On my RV7a I fed them through the firewall, it seemed like the sensible thing to do.

FWIW I had issues with my AP maintaining direction and implementing unnecessary turns. In the end I tracked it to a corroded connection at the servo. I remade the connections and the problem went away. In the end a relatively quick and cheap resolution.

A report on an issue I encountered. Today my VPX licence disappeared. It was there yesterday but I realised it had disappeared when I investigated why my flap position widget no longer appeared on my D1000, replaced by a red X where it used to be and the hint 'CFG?' After some investigation...

I had to get the locked up screen 're-flashed'. I took it to a local Dynon dealer and they carried out the process. Then its a case of reloading some of the databases, reconfiguring the network etc to bring it back to a fully functioning system. I have a suspicion that the issue was caused by...

I just applied version 16. I have two D1000s. One of them , s/n 2003, is now locked at the Dynon splash screen and will not start. The second screen s/n 2124 has updated. I have a call in to Dynon and am waiting a reply. I am wondering if it is about the earlier version? I suggest those with...

2023 at this rate

People have been waiting so long there is very little chance it will come close to the expectations of the customer base. Not Dynons fault, just the nature of human beings.

I also tried again a few days after the initial error and my Skyview was working correctly. I also heard back from support saying I should send the unit in under an RMA. I have not sent the unit in for test because we are heading into Summer here, just having come out of lock down, and I want...

Thanks David. I sent the diagnostic file in last week, no response yet. The fault has mysteriously gone away, waiting I imagine to reoccur during flight. At least the standby ADAHRS failover worked.

Hi I have logged a case with Dynon Support but since it is Friday night there I don't expect a response soon, so I am wondering if anyone has any suggestions to help diagnose this problem. Today I received an error from my ADAHRS 200. The aircraft was in the hangar. Battery power was 12.1...

It might be possible to assign a sound to the operation of the knobs, different sounds for different knobs or off for those who don't want it. Probably achievable through a software upgrade, and then configurable to suit the individual.

Thanks for the ideas. I have a Classic and after much playing around it seems I can turn off every bug with the exception of 'baro'. No idea why this is, but it is no great inconvenience really.