Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
New profile posts
Search profile posts
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
jakej's latest activity
J
jakej
reacted to
airguy's post
in the thread
HDX high voltage/IO360/Odyssey PC680 battery
with
Like
.
This is an alternator regulator issue. It's quite possibly the "voltage sense line" for the regulator has some slight resistance (poor...
Sunday at 3:27 PM
J
jakej
replied to the thread
Unstable Reading from "Resistive" (not Capacitive) Fuel Sensor in Right Tank – Calibration Issue
.
Fantastic result- seems like it’s all okay now 😃 FWIW I’ve never found grounding an issue for the resistive or capacitance units &...
Oct 1, 2025
J
jakej
reacted to
ChrigelsRV8's post
in the thread
Unstable Reading from "Resistive" (not Capacitive) Fuel Sensor in Right Tank – Calibration Issue
with
Like
.
I thumped on top of the wing yesterday during the calibration. This helped a lot. the indication stabilized after a few second and for...
Oct 1, 2025
J
jakej
replied to the thread
Unstable Reading from "Resistive" (not Capacitive) Fuel Sensor in Right Tank – Calibration Issue
.
Ok - back to square 1, bear with me as I'm trying to understand your setup - Post #9 shows a resistive sensor type in an Vans RV -...
Sep 30, 2025
J
jakej
replied to the thread
Unstable Reading from "Resistive" (not Capacitive) Fuel Sensor in Right Tank – Calibration Issue
.
For EMS sensors it’s always better to use a ground from the Dynon EMS unit, you can pair them up if you don’t have any spare ones.😉 ps...
Sep 28, 2025
J
jakej
replied to the thread
TRAFFIC ANOMOLY ON SKYVIEW
.
Have you gone into Setup > Traffic Setup Menu and set the Show Ghost Targets option to NO? (see attached) Andre'
Sep 19, 2025
J
jakej
replied to the thread
OIL TEMP ERRATIC AND READS HIGH
.
Always connect to the EIS/EMS grounds - you can pair up the grounds if there are not enough individual grounds available - that...
Sep 19, 2025
J
jakej
reacted to
GKC Aviation's post
in the thread
OIL TEMP ERRATIC AND READS HIGH
with
Like
.
Did you set your connected sensor up as type 3 on the GP contact you connected it to? The GRT sensor has different resistance values...
Sep 19, 2025
J
jakej
replied to the thread
Problem with servo SV32 (D10A), always yellow ;;
.
Most likely not a wiring problem - if the network wires were incorrectly installed then you would get a message telling either 1 & 6 or...
Sep 10, 2025
J
jakej
replied to the thread
Carburetor Air Temperature Sensor Problem
.
Double check the location of the probe it may be in the fuel in the fuel bowl ? Don‘t ask how i know this 🙄. Suggest you remove the...
Sep 10, 2025
J
jakej
replied to the thread
Problem with servo SV32 (D10A), always yellow ;;
.
Maybe the shear screw is broken?
Sep 8, 2025
J
jakej
replied to the thread
Skyview compass uncalibration
.
Have you checked the ADAHRS mount security ? ;)
Sep 8, 2025
J
jakej
replied to the thread
Low voltage hdx indicator any advice please random goes low but system is charging fine ok
.
I’ve seen the exactly the same issue years ago,cleaned the pin contacts with a soft wire brush then flushed the gunk out with contact...
Aug 20, 2025
J
jakej
replied to the thread
VPX Offline
.
Understand it’s real hard sometimes troubleshooting online considering “We” are unable to see/know how your plane is wired. If I was a...
Aug 20, 2025
J
jakej
reacted to
airguy's post
in the thread
Servos Offline
with
Like
.
Intermittent electrical issues will give you gray hair and cirrhosis of the liver.
Aug 20, 2025
Members
Top