Search results

Hi, I have Skyview x2, Single EMS, Rotax 912uls, engine vintage 2011, with what I think is a Honeywell 956413 sensor connected to Pin 6, Power to Pin15 and black wire to Ground. Installation oil purge prior to inital engine start I have 0-4psi only showing on the Skyview but checked with...

Hi, I am at the intial wiring check/start up of my panel. I have 10'' Skyviews x2 with AP panel and Ray Allen stick trims wired through the AP panel. I have yet to set up or configure anything in the Skyviews. Currently the stick trims are inoperative and do nothing and I have a flashing red...

Hi, I am installing two Skyviews in a composite panel. I have in the back of my brain the notion that the case needs to be grounded in a composite panel but I cannot find where it says so in the installation manual. Can you confirm please that this is necessary and if so the size of the screw...

I am wiring a SV-AP Panel with Ray Allen aileron and elevator trim servos to eliminate trim separate trim controls or relays. Can you confirm the trim circuit breaker value I should use for the installation please. I am slightly confused. In the installation manual it shows Pin 9 @12v 4amps. Is...

Hi, Please do forgive my ignorance if this has been explained before and without getting into the pros and cons of legal compliance and its issues... The Dynon transponder has, as I understand it, an extended squitter so does this mean that mean that when installed with the SV-250 GPS in a...

Hi, In a two Skyview setup are 2 Wi-Fi adaptors necessary? Will a loaded flightplan into one unit go to both Skyview panels? Also is the shipping date for the Pocket FMS Adaptors immediate? or like the remote Magnetometer are they not available until later in the year? Thanks, Alan.

Hi, I wish to fit a CS Prop Controller in addition to Skyview on a Rotax 912ULS engined aircraft. How do I solve the Tach takeoff for two separate instruments? Splitting the signal etc. I see that the SV-EMS 221 for the Rotax912iS has an RPM output pin for a CS Prop controller but the SV EMS-220...

Probably a strange question but personal preferences possibly coming in to play here. The Roll and Pitch trim on all views I have seen are on the EMS page. Is there any way that they can be configured to display on the PFD display? Thanks, Alan.

Hi can you help please. I am sure you have answered this question many times before but I can't find the answer in search. Can you confirm..... If I install the SV-AP module can I still install it and retain the option to use the RAC 205 stick trim buttons if I wish? In other words it then gives...

Sorry but some info needed please that I am sure you have answered umpteen times. I am still in the pre purchase decision phase.. Trying to weigh up the Pro's and Con's of Internal v External GPS What info from an external GPS (say 695) will be displayed on the Map page.? All FPL route data...

Hi, In the installation manual Doc 101320-017 revR, August 2014 it says the SV-D700/D1000 current draw is 3.5 amps per display average. Can you confirm that the D700 has the same average current draw as the D1000 please? I would have thought the smaller screen would be less. The SV D1000T also...

Probably a basic question but I am new to Dynon, can't find the answers and trying to make some pre purchase decisions for a daytime VFR aircraft:- If I fit 2 Skyview display units will I need two ADARHS 200 modules and two SVEMS 220 modules plus two GPS 250's or can I manage with one of each...

This may be a dumb question.. Still at the designing panel stage and having flown steam for 30years I am somewhat nervous about my brains ability to disseminate all the information quickly that is available in one unit whilst flying! In a 10a for instance can the screen be easily and quickly...

Hi, I am just at the deciding which route to take stage. If to go for the 10A or 180 or whatever. I am also definitely a novice at dealing with all this advanced technology ...so go easy! Can you tell me if the barometric pressure can be changed on either of the above units from inches to...