Search results

Time for a reset - Are you still using the home made Pitot/AOA ? IMO, & I’ve done many installs, the issue is with your installation regardless of any troubleshooting you’ve had done. Have someone else sort it out properly AFTER a genuine Dynon heated/unheated Pitot is installed. PM me with...

Rhino - correct, depending on what equipmentsoftware Jayp has. IF the servos are going back for SB-001 then I’d suggest he has the SB-002 (Gear only) done at the same time - that’s a much more cost effective approach IMO 😉.

I’m on vacation however I‘ll pm you later today - just need to know if you’ve done the Servo neutral cal & checked that there is no slop in the aileron linkages?

The A/pilot CABLE IS DIFFERENT to the standard network cable for a reason. The network wires ie pins 1&6 + 4&8 are the network wires common to all the other network wires needed for the system to ‘see’ the other network items. Grounds (I allocate to pin 2) & power (pin 2) are 20 awg with ground...

Brilliant idea Paul - I don’t know why a few of us didn’t suggest that. Then again not knowing/seeing the install details is one of the difficulties around ‘online’ troubleshooting. 😉. Those electron critters are just waiting to pounce 😂.

I’d update to version 5.6 (last one ever) & see how you go, worth a try however I’d check with support@dynonavionics.com first.

Jaba- you can go down that path again, i have done that several times. I use a PM1200 & the AMX 2/10A ( Maker Plane) with a 3PDT switch for the TX. I’ll send you a text.

As S Watson said - it’ll be the 5volt wire or ground - that’s the only common thing to both & it’s more localised as the fuel pressure is working ? and it’s using the same 5 volt input.

Peter, all important ,essential, critically equipment should be on independent circuit breakers or fuses. Doubling up those items can create an unwanted stressful situation If one ‘blows’. I see what’s on the diagram however you can do better. The. ‘accepted norm’ is one ’breaker’ for the above...

Gotta ask - why did you parallel the power to 1 x C/B ? That's not the way to do it, you need independent power to each servo so that IF one goes awol it will not impact the other one - makes troubleshooting a lot easier too. Wiring the way you have could, in some circumstances, result in both...

Thank you for being humble enough to say that.😉

Charly - I’d just connect 1of them temporarily to find out & also use a heat gun to confirm ops, applies to the EGT & CHT.

I'll call you a bit later this morning ;)

Riseric, I’ll pm u a diagram of what i use - is easy to follow & uses the existing 15 pin dsub connector numbers so its a plug & play solution & can be kept for future use if ever needed. No need to mess with anything else, just plug into the a/p panel connector.

I have a diagram on how to do that if you want, it uses the same pin numbers as the 15 pin connector ?

A while ago, before the SB, I had several customers with issues with the a/p panel. My temp solution to enable them to fly was to make a plate, same size as the panel, & mounted a biased switch on it to just control pitch trim servo (pitch was all they really needed) while the issue was being...

FWIW I’d do is try your a/p panel in another plane - NOT a ‘loaner’ in your 8. If there is a problem in your 8 other than the a/p panel it could cause damage to the loaner unit, if your a/p panel does have a fault it will show up in the plane you test it with.

V-tail - FYI, altitude is sent from the Dynon into the IFD, helps a lot when you want to do GPS VNAV approaches 😉.

I’d use the Maker Plane AMX-2A or the AP60 Audio Mixer, they are very small😉.