Search results

I thought the same thing, but DTW and DIST TO GO are not the same value, indicating that there is indeed another waypoint between the plane and the destination? If I recall, NEXT WPT should be showing the name/designator of the waypoint, not a calculated value, correct?

"Upgraded" to the OLED version. Was installed in a current Zenith build, but never flown, so basically new.

Same thought. I've gone over and grounded every case directly to the airframe for just this reason, but no change. It's all just so odd. I've put out a call for a local Dynon/audio guru to come to the house and "just do it." No bites yet.

The wrap is only on the face of the panel, the edges where the panel mounts to the airframe is still bare. I might try taping up all the Dynon gear and reinstalling it.

The jacks were not removed, they're mounted under the seats with fiber washers as before. The audio wiring harness was not moved or changed, the intercom was merely unplugged from it.

The weird part about that is, the panel was bare aluminum before, and it was working perfectly for almost 2 years. Add some insulating vinyl, and suddenly I have more grounding? But I think I'll test the theory by removing the Dynon gear from the panel and doing a "bench test" with everything...

I had the whole instrument panel pretty much done, everything worked. Then I wrapped it. I pulled everything out of the front that could be (HDX, OLED COM and Intercom) and pulled everything else from the back (prop controller, breakers) so each item remained pretty much in place, electrically...

Seems normal to me. When the PSI drops below 2.2, that's the event which fires the alert. If it stays below 2.2, there's no event.

Just the one on the battery.

Seeing in the EarthX documentation that it's normal and expected is enough for me, for now. :)

Found the answer. Should have used better search terms. I'm working on a new install of a Rotax 912iS in a Zenith 750 with a Dynon HDX in the panel. I recently noticed that my EarthX fault LED indicator was on, started troubleshooting, and this is what I've found: - With main relay on, engine...

The harness supplied with the EMS-221 was mis-wired, the green and blue wires were in the wrong holes. I moved the pins to the correct holes and it now works. See https://www.rotax-owner.com/en/912is-technical-questions/9481-photos-of-rotax-dynon-can-wiring?start=5#p34089 for more info.

Having trouble getting Rotax 912iS data on the Dynon HDX, they're just not talking. I'd love to see photos of how people have connected the Dynon CAN lines (blue and green) to the Rotax HIC A and B connectors. Any real photos of real working installs?

During a late-night wiring session, I forgot that the 103757 sensor is a 5v device, not a 12v device. Did I kill it? My fuel pressure widget is always crossed out, and the VALUE column never populates. But the RAW and CAL numbers do change if I blow into the opening. The widget did work when I...

I’ve confirmed the CANBUS connections from both the Dynon and Rotax 912iS installation manuals, but what about the Rotax CAN GND connections? Do these go to a shared EMS ground pin? Airframe ground? Not connected? HIC A 6 CAN_H1A >> Dynon EMS 36 HIC A 5 CAN_L1A >> Dynon EMS 37 HIC A 4...

It's been suggested, but since the knob has no set screw, the pressure of the o-ring pushes the knob to slide on the shaft, reducing the tension back to zero. Many folks have commented that their knobs are the same as mine, so it's "normal."

Unboxed my SV-COM again today, preparing to cut my panel for install, and noticed that the volume knob has no tension at all. The HDX knobs are clicky, the COM tune knobs are clicky, the Intercom knobs have a good bit of resistance, which is what I'd expect of any non-clicky knob. The COM...

I've gone through the Map Items list but can't find "Traffic" mentioned anywhere. I'd like to have traffic appear only when the map is zoomed down to a certain point (maybe 5 or 8nm). Seeing our local ClassB traffic all stacked up, obscuring my plane, when zoomed out to 20nm is just an absolute...

I'd look for "silicone led strip" or "EL wire" and see where that gets you. Such as, https://www.adafruit.com/?q=silicone+led+strip&sort=BestMatch https://www.adafruit.com/?q=el+wire&sort=BestMatch

It was clear. I'm just still confused why the GPH display would not inherit and calculate fuel burn based on this adjusted value.