Search results

Recently I have been getting a CPU TEMP HIGH message. I think I have also seen a CPU TEMP CRITICAL message. This unit has been working great for 13 years. Just started seeing these CPU TEMP issues now. Outside temperature was actually cool (60's) during today's flight when the CPU TEMP HIGH...

Yesterday the three SV-HDX1100 in my RV-10 rebooted during takeoff. Each time during takeoff and full throttle. On Sunday when I encountered the first SYS EVENT 3 it was during a Takeoff stall. I have sent the diagnostic logs to Dynon for the reboot this past Sunday, but no response yet. I...

I have an RV-10 with Dynon Skyview HDX and VP-X PRO. In the Dyon Skyview setup, I have FLAP Position, AILERON TRIM Position and ELEVATOR TRIM Position set to VP-X. In Dynon Skyview Sensor Data, I can see the position values for FLAPS and TRIM change as I move the FLAPS and TRIMS. The position...

I plan to update my original Skyview 10" Dispaly with a Skyview HDX 10" display. I want to make sure that all current settings/configuration is moved to the new HDX display. What do i need to do to make sure that I am able to get all the setting/configuration moved to the new HDX display...

I recently installed the SkyView Autopilot Control Panel. Installation went well. It was discovered and code/FW loaded. I still have the Autopilot setting as Simplify and not Expert. The problem that I am having is that every once in a while I get a message that the Level Button is Stuck. In...

I installed the SV-COM-T25 Transceiver with the SV-COM-PANEL as my second COM radio through a Garmin GMA 340. The transmit is working great, but the receive comes in too low. In order for me to hear the receive, I have to bring the volume all the way up on the SV-COM-PANEL and it is still too...

Question/Help. I installed the SV-XPNDR-261 in my RV-6A. I have an original 10" Dynon Skyview Display. I am getting my GPS signal to the SV-XPNDR-261 from the Garmin GNS 430W. The Transponder menu shows compliance = YES. On my first flight I was told that other airplanes with ADS-B In were...

I am trying to order a couple of AutoPilot Servo Shear Screws from Dynon or the Shear Screw kit part number 102991-000, but there seems no way to order the screws. I tried removing the shear screw and broke the head of the screw. How can I order the shear screw from Dynon? Thank you...

I recently loaded the SkyView Classic 16.0.1 Software Package (3/25/2021) and for some reason when I go to MAP/Direct To and select an airport and then Direct To, it does not draw the line from my current location to the airport that I am trying to go to. Works if I do this on my initial...

I am installing the GRT CS-01 in my Skyview system and I have a couple of questions: 1) How many times do I need to loop the wire (8 AWG) going from the alternator to the load buss? 2) I will be connecting the BLUE wire of the GRT CS-01 to the EMS D37 pin 18 (+5V). Is that correct? 3) Any...

The Display D37 connector has two Power Input pins (1 & 20). I was planning to connect one power pin (1) to the VPX and the other pin (20) to a backup Power Bus that I would manually switch to if there are any issues with the VPX. My question is if this is the best way to supply power to the...

After a number of years I decided to connect the heated Pitot Status line from the Heated Pitot/AOA controller to the EMS. I connected the status line to EMS D37 Pin9. The heated pitot works, but the status line (white wire) from the controller does not work. I used a volt meter and have zero...

I have an original Dynon Skyview. I also have a Garmin 327 transponder. I would like to have the Skyview connected as the altitude encoder for my Garmin 327. How do I connect it and how do I need to configure it at the Skyview and at the Garmin 327? Thank you...

I have had my Skyview System since 2013. Everything has worked great except for the AMP reading. I have been unsuccessful getting it to work. I have the shunt between the alternator and the aircraft load. I am using pins 24 & 25 from the EMS DB37 with a 1 AMP fuse on each wire for pins 24...

I have been using the original Skyview system in my RV-6A since 2013 and love it. I am now building a Vans RV-10 and I am planning to install 3 Skyview HDX, but when looking at the Skyview comparison chart (link below) it states that VP-X Integration is coming soon. I have seen this message...

Does anyone know if you can use the Dynon Skyview EFIS as a CDI/glideslope with the 480W? Have the EFIS display the CDI/Glideslope. Thank you...

I have the Dynon Skyview Classic which was installed in 2013. Over the years the RPM reading has become unstable and it spikes between 3000 to 5000 RPM when at full throttle. It had worked good at the start of 2013. I have a LASAR ignition with the RPM lines connected to EMS 37 Pin Connector...

Has anyone installed a capacitance fuel sender into an already completed fuel tank/flying RV-6A that has a Dynon Skyview system installed? I would like to move away from the resistive senders in the tank now. If yes, what capacitance fuel sender did you install? Thank you...

Has anyone connected the Audio Out from the Skyview to a Garmin GMA 340? What pins on the Garmin GMA 340 did you connect to? Here is what I am thinking, but want to make sure that it is correct. Skyview D37 Pin Garmin GMA340 J2 Pin Pin 13 - Audio Out Left Pin 26 -...

I just installed the GRT Oil Temp Sensor (Lycoming O 360). I have a Skyview Classic in my RV-6A. I have not started the engine, but just bring up the Skyview system and it reads -11 degrees. Figured that I would just switch the wires and still reads -11 degrees. Anyone use this GRT Oil Temp...