Search results

Problem/Desire: Power Skyview display and supported items from 2 separate batteries. The purpose of which is to power up the Skyview system to input flight plans and have ems ready for engine start. Once engine is started, oil pressure values are immediately available. Starter and second power...

I have a Skyview 10" classic and Garmin 430 non Waas. During the test screen on the 430, the Skyview HSI displays the CDI offset from center. But, there is no glideslope indication. I've had the 429 wiring tested and confirmed that I didn't fat finger the pin numbers. The 430 just returned from...

Does anyone have the data format for the Dynon ADS-B receiver ? I believe it is an "enhanced" GDL90 format, but cannot find any documentation. I want to send ADS-B data to multiple devices. I'm thinking of connecting an ESP-32 micro controller and writing a program to convert the data to...

How do you setup Skyview to send and receive information with an Avare table ? I would like to , Send flight plans created on the tablet to Skyview Recieve Ads-B info (weather and traffic) from Skyview I have added my Wi-Fi adapter to Skyview and configured it; added airplane info and...

I am testing the canopy wiring and setup before installing. I have a microswitch attached to pin 22. It is sending 12 v to the pin when the switch is open. To the same switch output I have a small warning light, recieving the 12v. The light is grounded seperatly. In the Dynon setup I have pin 22...

I have an EI Ft-60 fuel flow transducer. It was installed before the Dynon was installed and ran fine. I have wired it per the manual rev AE on page 7-57. Black - pin 30 White - pin 14 Red - pin 15 The wires ring out just fine. I have configure the Dynon Ems mapping to fuel flow and set the...

I'm updating my aircraft with a full Dynon suite. I've been running EI engine instruments for years and they have been bullet proof. But, I don't have room for both the EI instruments and the Dynon screen, (two place tandum aircraft). So, I'm trying to reuse the EI sensors. I've found out that...

Need some help with the connection between SV Com-425 and PS Engineering 5000EX. Symptoms Display on SV-Com panel show STUC Active frequency says 118.500 If I dial in the local ASOS display sometimes shows Airpor ASOS but Active frequency says 118.500 and no ASOS is heard Dynon...

I'm upgrading my airplane with a full Skyview Classic system, including engine monitor. My airplane has a canopy, landing brake and nose gear warning system. This system is notoriously unreliable and is based on grounding the micro-switches on the various systems. I was thinking of using an...

I was doing some bench testing on my Skyview Classic. I notice if I put a "Y" connector between the screen and the ADAHRS, the light doesn't turn on and I get a X. If If I shut down the system and remove the "Y"connector on the network, the ADAHRS works fine. What is going on here ? I have a...

Installing my roll and pitch servos. When looking through the installation guide, chapter 10 "Circuit Breaker/Fuse" it states "We recommend that electrical power for the autopilot servos be protected with an appropriately sized circuit breaker or fuse that is accessible to the pilot while in...

I am bench testing my skyview attempting to integrate it with a 430 non-waas. I have wired the 429 box to the 430 using the instructions and diagram from chapter 11. Just to double check I rang out the pins on the 429/25 pin connector to the Garmin's P4001 and P4006 connectors. Everything...

I'm working on the bench solving install design problems. I'm currently running 11.x firmware and am aware of the 14.x problem. So I wanted to download 13.0.3 firmware. But I can't find it . Anyone with a URL for the download ? thx, Mfz

I've noticed that the SV can send different types of data to the built in serial outputs. I have an interest in sending data from the SV ADSB reciever to a tablet. The serial data output per Rev N dated January 2013, of the SV installation guide includes : ADAHRS Air...

I have an existing aircraft that I'm upgrading to Skyview. The aircraft is currently flying regularly and am building the new panel on the bench. My current engine gages are all Electronics International (EI). I'm trying to figure out if I can reuse all my existing probes. Currently have ...