Search results

Anyway to convert GPS postion coordinate format displayed or for entering into waypoints? Let's say from Degree,Decimal Minute to maybe Degree, Minute, Second or Decimal Degrees... Thanks!

Planning on doing a panel change to include two Dynon HDX 800 displays. I will have two SV D-700 Classic displays available for sale. I can save you approx 20% off buying new. Will sell both for $4000 or individually for $2100. One display repaired and refurbished by Dynon last year for...

Had to send my 7" Classic EFIS back to Dynon for some issues with reading files during startup. Roundtrip from the East coast and back along with diagnostics and repair took less than three weeks. There were two issues: (1) some sort of firmware/software issue which needed factory...

As above, smooth air and on occasion during flights I get the audio announcment for "G's" Any ideas?

Anyone else hanging up on the download for the latest chart update?

I would like to have 360 degree traffic awareness/display from the Dynon ADSB to my Dynon MFD. Is this possible? Seems like I can only display traffic within the 9 to 3 "O'clock" sector based on my screen view setting. Would be nice to see traffic overtaking or converging from behind. Thanks...

Out of the blue with no files recently updated and multiple flights I started to get the "EMS SFG FILE MISMATCH" caution message. Here are the files from the respective USBs from each 7" Classic. Any insight or advice on how to proceed clearing this up and why this might have happened...

Anyone else having trouble updating the approaches and diagrams for the new cycle? :-? :-? Everything else no problem. Open for any ideas, waiting on SA tech support to return email Thanks! Dave

Kudos Dynon!! Recently swapped out my SV32 servo for the SV42 to resolve a pitch slipping issue with my STOL CH750.  It appears that air loads on the elevator are a bit too much for the SV32.  Pulled the servo on a Friday and one week later received and installed the SV42. System software did a...

Just requested/received report yesterday for my system which includes the 261 transponder, 2020 GPS, and 472 with 15.3.3 software and firmware update.  Passed with flying colors and compliance.  I do have a question though... The NACv accuracy values (AVG, MIN and MAX) are each reported as "4"...

I've got the Dynon heated Pitot/AOA and have configured the Pitot heat status line as a contact type sensor for display on the SV-D700 PFD. I am only seeing 5V on the pin and no variation as I cycle Pitot heat off and on when looking at the sensor debug page. >:( Pitot heat functions as...

Has anyone seen this msg? Trying to figure out if I need to remount my ADAHRS. THX! : :-/

Is there any benefit to reducing torque values of the servos to a point where they "normally" don't cause a slip message. My pitch and roll servos seem to work fine currently set at 100% though I am still trying to tweak sensitivity and gain for the overall system operation. There is likely...

In Phase I flight testing and starting to inflight tune the AP servos.  Using the Dynon produced flow charts for  inflight tuning.  Two SV32 servos installed on STOL CH750 along with AP control panel.  In simplified mode TRK/ALT along with HSI/ALT seem to hold altitude OK (smooth air).  When...

Is it possible to create a user defined area on the SV map? I can create a flight plan with 4 corners of my Phase I test flight area, but was wondering if there is a better way to do it? Thanks! P.S. Kudos to the whole Dynon team...the SV system has an amazing amount of capability and well...

Is it possible to do a ground calibration of the the compass on other than cardinal headings of North South East and West. In other word, does the process allow for entering a known magnetic heading; i.e. known runway mag alignment Thanks!

Recently filled my two fuel tanks for leak checks. Previously had defined my tank quantity sensors and fuel quantity widgets with initial colored ranges. With full tanks (but no calibration accomplished) one of my tanks is displaying the ? CAL but with ranges displayed on the widget, and the...

Thoughts and input please... I have two 15 gallon main tanks which both feed to a 1 gallon header which serves as the source and return for a fuel injected engine. The main tanks have resistive type fuel senders. To calibrate the gauges, is it feasible to top off the tanks and repeatedly...

I have two D700 displays running in my panel. If I need to remove one for repair and run with a single D700 what do I need to do with the vacant connectors? Somewhere I recall something about a null connector of some sort being required. Any insight from users or Dynon will be appreciated...

Initial install..no problems. After a couple of engine starts and skyview database update attempt, I got a message about previously recognized skyview modules no recognized/found. Had to exit update, did a network config check and found that the servos were no longer listed and can not get...