Search results

Same here- stuck at 99%. Had to cycle power to Xpdr to correct. 1,2&5 reboot of display did not correct. I have a single display. Kurt

I still do not have the cycle that starts today. However, there is hope they did not go out of business. Got this email this morning from Seattle: Hello Kurt, and thank you for contacting us. The new cycle (2508) of ChartData is being released now, in phases, by avionics/app type. I do not...

If you Google Seattle Avionics troubles you get this back.

still no database downloads available at this time (7:16 PM Texas) Kurt

Another thing to consider is the location of the shunt and the EMS differential pair of wires connected. It only takes 50mV (.050 V) difference between the wires to indicate 50AMPS. These wires must be a twisted pair and should be isolated from other high current carrying wires. Kurt

Dave from Dynon confirmed that there is an issue with the logging of values greater than 999.9. It is a bug that they are aware of and working on fixing it. kurt

Only the TRIG acquisition.

I have a custom sensor defined in my .SGF, shown below. My HYD Pressure is for the landing gear pressures, UP and DOWN. I routinely see pressures at the 800 to 2000 PSI range on the Skyview display. However, when I download the User Data files the CSV column that contains this parameter is...

I have seen this when 4 devices are connected to Skyview WiFi. If your iphone is on the same account as your ipad the network info is shared. So, if you have your tablet set to auto connect to Skyview, most likely your phone will do also. Unless you specifically tell your phone not to auto...

I got the system event 3 on shutdown today. Anybody know what it means? downloaded the diagnostic log and user logs. Kurt

I got the system event 3 on shutdown today. Anybody know what it means? downloaded the diagnostic log and user logs. Kurt

On the ground, Try isolating the source of the problem by taping over the static ports and see if the problem stops when engine is running. A vacuum on the static will indicate airspeed. Maybe you have a serious static leak that is putting a low pressure in the cabin when prop blast is blowing...

I was flying around the DFW area last Wednesday and never got a single In-flight weather product on my Skyview system or my connected Ipad. There is a NOTAM out saying Traffic ADS-r, and TIS-b may not be available In this area. This NOTAM is still in effect until 202507282200. I received...

I had a EMS module failure that took down the Skyview buss. Just big red X’s. I have a D100 for my backup. Once I got on the ground I was able to disconnect the EMS and was able to get my PFD back, but no engine info. A totally independent system is your best approach for a backup.

That is great news Brad. I would be interested in this also. I have a HDX and a IFD 540. Could not get the SV ADSB data on the IFD. kurt

That is not enough burn to adjust the k-factor. i would not adjust until you burn close to a full tank. Then to fine tune, add up a couple fill ups to get a new total fuel burn, actual and SV values. kurt

Foreflight is totally broken with the IFD and Skyview on same network. The Foreflight update that pushed just before Thanksgiving broke it. At least on my installation, Skyview w/ ADSB, IFD 540, and Foreflight all on Skyview WiFi. It will no longer gets position (GPS) from either IFD or...

Tried that several times. Notice I am receiving ADSB data. But the GPS is not being decoded. i tried connecting with FltPlan Go. It connects and works good. It is just another software issue with Foreflight. They keep pushing new features but fail to test if it affects the old features...

Foreflight updated just before Thanksgiving. I can no longer get Foreflight to use the Skyview GPS or my IFD gps. No position data available. I normally have it use the IFD gps but now it won’t see either. No longer get the message if I want to load flight plan to the IFD. So, Foreflight is...

My Avionics shop had another customer with a new Skyview system that the WiFi adapter would not be recognized by the HDX display. After trying another WiFi with same results tried moving it to the other port. The other port worked. The first port works good with the usb mem stick. How do you...