Search results

Thank you PaulSS. My sentiments exactly!

Thanks for your reply, Rhino. It certainly sounds like the kind of answer the LAA will love and it ticks the box. 🤣

Any answers gratefully received.

In the UK, the LAA, regulatory authority, has asked me to provide certain information. It regards the ‘protocol’ or the means by which the Dynon transponder, Dynon GPS and Dynon ADS-B communicate with each other. Is it NMEA? I’ve no idea what this is, nor do I care. I just need an answer. Thanks.

I have a Skyview 1100 HDX. My flaps are configured through a Vertical Power VPX. I can't figure out how to change the UP setting on the Skyview flap widget to show 'Zero' (0) when the flaps are completely in the UP position. It shows 3 degrees down. I think I managed to fix this before, some...

Thank you all for your inputs. Never did figure out where the HEX code of 435432 came from. I think Octal and SkyView software version inputs were red herrings. But thanks, anyway, for these suggestions. In the end, taking some of the advice from above, I deleted the HEX code in the Skyview...

Just to tidy up this thread. After performing a test, at Dynon’s request, using the pin configuration page, it was established that there was a problem with the pitot heater controller. I opted to purchase a new one. Dynon gave me a small reduction in price. Still haven’t flown the aircraft...

Thanks for that. The battery could have been a bit low with all the configuration I was doing today.

I suspect the right side knob of my Skyview 1100 Display has lost part of its function. It appears that when I push the knob that function works. However, when I try and rotate the knob, nothing happens. It means I can't change numbers or letters, scale settings etc.. Any ideas?

I attempted to calibrate and test the AP roll and pitch servos on the ground today in a new-build RV7. In addition to the servos, I have a Skyview HDX 1100 installed along with electric roll and pitch motors. The servo calibration appeared to go fine and the system asked me to then proceed to...

On the widget displayed on the SkyView screen, I have it showing ON and Green continouosly, irrespective of the pitot heat switch position. I configured it as per the pictures attached below. Very confusing.

Yes, pin 10, and I mapped the sensor as per 15-1 of the Installation Manual.

I recently connected the Dynon pitot heater signal wire to my EMS. I think that I was mistaken in my understanding of what information I expected the Skyview display pitot heat widget to give me. I had previously understood that if I switched on the pitot heat, the display would indicate to me...

Thanks lancair360. I’ve ordered 2 WiFi adaptors. Seems pretty cheap (2 x $35) for the extra capability.

Thanks for all that info GalinHdz. It’s all much clearer, thanks.

Thanks for the above 2 useful replies. One more question, if I may; my understanding, now, is that the Skyview Wi-Fi adaptors (1 x per Display, as per Page 15-13 of Dynon Skyview HDX System Installation Guide) are no longer required, since all can be achieved through the transfer of .gpx files...

I feel that the answers to the questions I am about to ask should be obvious to me, but they're not, so here goes anyway. I am some months away from flying with my Skyview HDX. It may be (probably will be) that there is no ISP provided WiFi, nor even a telephone signal anywhere near the hangar...

I’m pleased to report that the problem has fixed itself. I gave it a good talking to, using a few chosen words, before heading off for a bite to eat. When I came back and switched it on, it was magically fixed! Happiness!

Suddenly, out of the blue, the left HDX1100 display has a problem. When the 'Display' button or the 'Menu' button is pressed, the screen does not display what it should do, it more or less goes blank, with the exception that the top bar still shows frequencies and squawk. When I use the other...