SkyView 12.2 and Remote Magnetometer Available...

[Dynon]

Dynon Avionics is excited to announce that SkyView software 12.2 software is now available for download. SkyView 12.2 features support for the new SV-MAG-236 magnetometer (available to order now), an update to its transponder software to support 2020 ADS-B rule compliance, and improvements to SkyView’s ADS-B weather and TFR display capabilities.

As always, a full list of changes is available, as well as always up-to-date documentation.

 

[tommyturner]

I tried to download the new sensor file dated 4/28/15 separately because I need to modify it but the link gives me a sensor file dated 1/15/2015. Is this the new one? If not then where can I get the new one.

 

[Dynon]

That was a type-o. The actual file hasn't been updated since our last release in Jan (12.0). The date is now fixed.

 

[RV6-KPTW]

I can't find any system software on the "Dynon SkyView System Software" page greater than 12.0.

Announcement in advance of website change OR the system software is not updated?

Thanks

 

[RV6-KPTW]

I can't find any system software on the "Dynon SkyView System Software" page greater than 12.0.

Announcement in advance of website change OR the system software is not updated?

Thanks

 

[preid]

http://www.dynonavionics.com/docs/support_software_SkyView.html

 

[preid]

I noticed one of the "improved" features was "Fuel computer no longer compares fuel computer totals to measured fuel in aircraft that do not have in-tank fuel level sensors."

Where was this comparison? I have level sensors but I am trying to determine what and where this comparison is?

 

[dynonsupport]

It's on the fuel add page for the fuel computer. It shows you hos much we think is in the tank via the sensors and there's a "Match" button to copy that value to the fuel computer.

 

[RV6-KPTW]

Reidvator in his reply has sent me to the same page that I noted in my post but I still don't see version 12.2. I do see a lot of version 12.0 dated 1/21/2105.

I think I read that entire page several times. Should there be new system software posted?

What am I missing?

Thanks

 

[preid]

clear your cache and reload page.
Here is direct link- http://www.dynonavionics.com/downloads/Software/SkyView_12.2_US_Package_Apr28.duc

if you jusy want firmware and not all in one package-http://www.dynonavionics.com/downloads/Software/SkyView-12.2-dynon_update.dup

 

[RV6-KPTW]

That direct link did the trick but gosh, shouldn't that cache take care of itself? I feel like I have more important things to pay attention to.

Thanks for the fix.

 

[Carl_Froehlich]

Just installed 12.2. Did the "ADSB compliant" page and got a "no" with the message to change the GTN-650 serial output from "ADSB" to "ADSB+". Did so and now it says I'm compliant.
It does not get much easier than that - thanks.

Carl
RV-10

 

[waveflyer]

I have just loaded 12.2 but made no alterations to the system. At start up the nav screen showed a red cross but eventually loaded the nav map.
During the trip the nav map dropped out on a few occasions to be replaced by a red cross but only for a second or so.
Is this a bug, how do I fix it?

 

[dynonsupport]

A red X on the map means no data is being received from the GPS. Not just that it doesn't have a lock, but zero data is getting to the screen. This is usually a broken wire.

You may have a loose wire that is just a coincidence it happened at the same time as the software update. We haven't had other reports of this.

What software version were you on before?

 

[hoyden]

Can the fuel match on power up be disabled? I have an RV6 and I get this every time I start up. The fuel sensors read different values in level flight vs tail down. I looked through the installation and pilot's manual but maybe I missed it.

 

[dynonsupport]

Yep.

SYSTEM SETUP->AIRCRAFT INFORMATION-> FUEL ADDED DETECT

 

[waveflyer]

A red X on the map means no data is being received from the GPS. Not just that it doesn't have a lock, but zero data is getting to the screen. This is usually a broken wire.

You may have a loose wire that is just a coincidence it happened at the same time as the software update. We haven't had other reports of this.

What software version were you on before?

The previous version, I keep it up to date.