Search results

  1. C

    Network cable pinout wiring

    When creating my own Skyview Network cable, I thought I should connect pin1 to pin1 , pin2 to pin2, etc., all the way to pin9 connected to pin9. But when you look at the end of the female DB-9 connectors on a network cable that shipped with my Dynon HDX system, and do a continuity check on them...
  2. C

    Com Not OnLine and transmission weak and unreadable with no sidetone.

    Today I had issue with Transmitter on Com Transceiver (SV-COM-C25 with SV-COM-425). Reception was fine on all frequencies, but I could hear no side tone when I pushed PTT button and spoke, and although ground control could hear me but said that my transmissions were weak and unreadable. When I...
  3. C

    ELT compatibility

    What (if any) ELTs can accept external GPS data from the GPS-2020 ? How about the ACK E-04 406 MHZ ELT (Iavailable from Aircraftr Spruce for $611)? ACK E-04 406 MHZ ELT KIT WITH WHIP ANTENNA USA | Aircraft Spruce
  4. C

    IFlyGPS

    Has there been any testing or compatibility work done between HDX wifi and IFlyGPS? Specifically, related to uploading flight plans, and/or downloading ADS/B data into tablet over wifi? I have been experiencing intermittent data transfer failures, (even when wifi shows successful connection)...
  5. C

    Skyview network connection fault

    What does this mean? The servos staus show as ready, and they are working okay.
  6. C

    Accuracy/Consistency of CHT Download data

    How accurate is the Cylinder Head Temperature readings output by the Skyview system? I have Lycoming O-320 E2D, with Dynon HDX, and all Dynon engine sensors installed. The CHT sensors are in the Lycoming standard CHT Sensor ports on the Intake manifold. I had a possible CHT over-temp the other...
  7. C

    Is Garmin SL-30 and HDX an IFR Navigator ?

    Is the Garmin Sl-30 COM/VOR/ILS attached via a serial port to the Skyview HDX, (with SV-XPNDR-261 and SV-GPS-2020), constitute an "IFR Navigator" for the purposes of satisfying FAA IFR requirements?
  8. C

    Version 16 schedule update ?

    With the obvious caveat that it's not done until it's done, it would be extremely useful to have some regular or intermittent updates on the release schedule for HDX version 16. Perhaps a short blurb on where you are in the software development cycle might be added as a thread on a discussion...
  9. C

    Assign existing waypoint to Bearing Pointer[s]?

    By default, bearing pointer 1 in the HDX points to the current GPS waypoint. You cannot control this. Many of us only have one nav source (an SV-GPS-2020/250), installed. In this case bearing pointer 2 is more or less useless. It would be a very useful enhancement to add functionality to allow...
  10. C

    Second GPS? Bearing pointer 2?

    What are advantages of installing a second GPS? I do not have a NAV radio. The Skyview HDX users guide (pg 4-19), says that you can connect the two bearing pointers on HSI to any one of the nav sources in the system, and the bearing pointer will "point" at the "radio station or waypoint". It...
  11. C

    "CAUTION",....."CAUTION",......"CAUTION", ........

    I am now having an issue. All of the A/P functions are working as advertised, but whenever the A/P is on I get continuous audible "Caution" messages over the intercom. They only last a split second, so I can never hit the message button fast enough to see the pop up window to see the details. It...
  12. C

    AOA subsystem

    I have a Rutan Long EZ, (pusher). The pitot tube is a simple tube, cut flush with the pointed nose of the aircraft so that the cross sectional is normal (perpendicularly aligned) with the aircraft longitudinal reference line. As I understand it the AOA subsystem in the AHARS determines AOA by...
  13. C

    Network detect fails to detect one servo

    Installing pitch and roll servos. When i connect pitch servo to hub and roll servo to display, network only finds roll servo. Configuration and test of roll servo is then normal. Ailerons deflect properly during test. So I then switch, and connect pitch servo to display and roll servo to hub...
Top