Search results

On Skyview Classic running 15.0.3 software, I noticed on the map pages when zooming in and out, I have the north up versus track up set to change at 50nm and that behaves as it should. Above 50 miles range it goes north up, and when you dial back below 50 miles it goes back to track. Now comes...

Hello Dynon, I have a dual Skview Classic setup with your ARINC-429 device taking data from a Garmin 430W to the Skyview for autopilot coupling of IFR approaches. I have recently installed a Garmin G5 in the panel for backup attitude indication and I want to also send the lateral/vertical...

I would like to see an option, maybe in the EMS page, to start a countdown maintenance timer to bring up a message to the user upon expiration. Maybe we could set a timer to expire on 681 tach hours for example, with the label "oil change due", something like that. If the timer is expired it...

Maybe I'm missing it, but I've looked fairly well in the Skyview documentation (I thought) and have not found this - is there an info widget for the screen for time to destination or waypoint? I've got fuel at waypoint, but can't find the time to waypoint?

How about a subsection here on the support forums for folks to buy or sell or trade Dynon products they have or want? You certainly have a good number of early adopters looking to upgrade, and there are always new entrants to the market looking to pick up budget equipment. Myself, I'm looking...

Dynon - for full IFR backup instrumentation, I'm looking at the D6 or D10A as a backup display to my Skyview in case of screen failure (or primary ADAHRS failure) in IMC. A complete standalone screen is valuable as-is with it's own magnetometer and ADAHRS just as a visual device, but can I also...

Dynon - with the standard resistive float sensors, during the calibration routine if only the empty and full points are set and the 2-gallon routine is not followed, will the system assume a direct linear response between the empty and full points based on the voltage difference and display the...

Dynon - which software versions on the 430W are required for the ARINC-429 interface to drive the autopilot for guidance? In this case I have the GPS-2020 so I'm good with ADSB, I don't need the ADSB+ software version for that purpose.

It would be nice if you could add an ADSB status indicator to the user log data dump. It seems like you've got an indicator for just about everything else under the sun in the there now, this would be helpful for troubleshooting.

I have a dual-SV-10" with software 14.0, just prior to first flight doing taxi testing in my 9A. Today my second (right side) screen started something new - it boots completely and comes up with it's normal screen, stays that way about 30-40 seconds, and then reboots. The reboot starts all the...

I'm trying to diagnose a problem I'm having with my elevator trim position indicator, I'm using a Ray Allen servo and feeding +5 volts and ground to the potentiometer on the servo, and returning the wiper signal back to the EMS. I've pulled the servo apart and confirmed that it's working...

Dynon - I've got capacitive senders in my fuel tanks, which have a different response to 100LL versus Mogas and would require recalibration when switching fuels. Is it possible to have a calibration in "standby", maybe as a different file residing on my USB stick, that I could load when I change...

I've got dual 10" Skyviews in my panel with the current V13 software and an Ethernet link between them. Which databases are shared via the Ethernet, and which ones require individual loading on each screen? Basemap Aviation/Obstacle High res terrain Low res terrain Very Low res terrain Also -...

On my display, CHT and EGT are displayed as Fahrenheit but in the data logs they are recorded in Celsius - is there a way to change that?

I recently did my first start, ran it three times, and in reviewing the log data I notice that the percent power calculation comes and goes. Sometimes a value is there, and it appears consistent with reality when it's present, but sometimes the value is missing entirely and shows up as blank. It...

I've got dual Skyviews with the latest software installed, and on bootup one of the messages I see is "Log file corrupted, logging disabled". How can I cure this?

I am approaching first engine start, I have dual Skyview with EMS and my fuel pressure and oil pressure both show top-of-scale with no pressure on them. My manifold pressure gauge indicates correctly, and all three share the same power source and ground. Do the oil and fuel pressure senders need...

Dynon - with the new video adapter that you've released for the Skyview, the next OBVIOUS  :D question is using it with FLIR. There are some FLIR cameras available on the market (not cheap, but available), can you give us some guidance on which ones would be compatible with the video in? And...

My setup is dual 10" Skyviews with the full Dynon suite of accessories. I have the servos, ADAHRS, and transponder connected to the #2 (right) screen, with that screen plugged into the Dynon 5-port bus where I've got the left #1 screen, ARINC, EMS tied into, all running 5.1 software. The...

Would it be possible to have a computed Mach number to set as a barber pole on the airspeed tape, since this is what drives flutter characteristics?