Search results

Dear Dynon, I am a huge fan!!  I just ordered my second Skyview for my Velocity.   I have been waiting for a company to develop an innovative product (at affordable prices) like this before I start the IFR rating process.  I will fly IFR for pleasure, and for increased safety. While...

Folks, I have started a website for my Velocity.  The Skyview install process is a big part of it.  I also plan to document how well it works in flight, especially when I begin my IFR training (when all features are available). I hope this will help.  Comments are welcome!! Safe Flying.  Tim...

I went to the airpot today to work on settings for the Skyview. I could not get my GNS-430 to work.  I am using the Approach Stack System and need to determine what serial port it is using (more to follow I am sure). I did hook up my Garmin 496 and could tell that it was connected to the...

Are the GNS-430 output settings the same for the D-10A EFIS? Meaning, should I have to change them for the SkyView?  Thanks  Tim

I am now setting up my SV system - hopefully I will not have too many posts   :) My Oil temp reads red X , even though the Dynon P/N shows up when I conduct the EMS sensor Mapping.  I have checked all grounds as well. I would like to get rid of the red X.  Any ideas?  Thanks  Tim

First, today I fired up the Skyview for the first time in the plane. WOW!! The displays are awesome.  I am bummed that I was stuck in the hangar, snow was way too deep to even roll the plane out to get a good GPS signal. However, I looked through the manuals and could not find the process to...

OK, I will ask the question before I hook up power.  Want to make sure that the appropriate breaker is a 5 amp one.   SkyView System no battery       - 3.5 amps SkyView with back up battery    - 1.5 amps (additional) I currently have the Skyview, battery, EMS, and GPS antenna.   I use the...

I realize the Autopilot upgrade will come out in the next software upgrade. Where will the future DSAB servo connections be made? Thanks  Tim

Is there a picture/diagram for the rear Skyview conncetions? Is there a specific connector one the Skyview designated for the EMS, and on for the ADAHRS? I did see that the ether net connection is for future use.  (I actually did read the manual  :) Thanks  Tim

I have received my Skyview and anxious for it to come to life!!  (I am using a Approach Stack wire system, and will not have it until next week) I am confused (again, not unusual), the install manual does not show the orientation of the ADAHRS.  I am sure I missed it in the manual. I assume...

In anticiaption of installing the Skyview - I have already removed, and sold my EFIS and EMS in my flying Velocity. Since the EMS-220 will be mounted on the inside firewall.......This weekend I will use the old wire harness for the EMS EGT/CHTs and make them shorter.  Engine is on the back :-)...

Folks, Could you give us your impressions of the new Skyview?  Tim

Dynon, I have read the product descriptions for the Skyview, and also reviewed the postings.  I apologize if the below have been answered, and I missed them. For my purposes, I am currently undergoing IFR training and I am learning more and more about the capabilities of my Dynon panel. I...

I have been very happy with my Dynon products.  I am reviewing the Skyview and determining my options. I currently have the EFIS D10A, EMS-D10, HS34, AP74, Remote Compass (with AOT probe) and the two AP servos. I understand that Dynon will exchange 50% for the value of the EFIS-D10A, and the...

On the GNS-430, I understand that the AIRINC settings are suppose to be:            speed           data In 1           High            EFIS\Airdata In 2           High             Off Out            Low              GAMA 42 HOWEVER, I cannot highlight the "EFIS\Airdata" on the Garmin setting...

Have you considered adding Approach Plates to the Skyview database?  Tim

Folks, I am on a family vacation and just finished up a three hour cross country trip.  I have a Velocity 173FG with the EFIS D10A, EMS-D10, HS34/AP74, and both AP servos.  I also have a GNS-430, and a Garmin 496.   Both GPSes are slaved via the Approach Stack System. I easily switch the NAV...

I currently have a GNS-430 and Garmin 496 working with my EFIS-D10A. (I also have the HS34/AP74 and EMS-D10 and both AP servos). While in the HSI mode, the GPS To indicator (small diamond) is not displayed.  The CDI works fine, as well as the rest of the GPS data.  Neither the GPS1 or GPS2...

Dynon, I recently received my EFIS-D10A back from service.  I had problems with the system after updating to 5.1.1  I installed, and it was great to see it come back to life!! While checking the settings, I had the RPM and clock on the left side of the screen, with the OAT settings on the...

How many GPS inputs can the HS-34 handle? I currently have a GNS-430 (GPS/VOR) for the HS-34.  I also want to panel mount my Garmin 496.  Can I hook it up to the HS-34 to drive the autopilot via the EFIS/ AP-74?  I would like to be able to switch between the Garmin 496 and GNS-430. Thanks...