Search results

  1. A

    Push to test Button for warning light problem

    Hi.every one I have 4 warning light on Ems ,alternator,canopy,fuel,and Pitot heater.and 03 voltage regulator which convert 24 volt or 28 volt into 12volt DC for warning light.the problem is that when I pressed Push to test button all sensor on Ems page showing cross.any one help me
  2. A

    Fuel flow greater than limit

    So its mean that FT 60 it self not faulty
  3. A

    Fuel flow greater than limit

    Hi every one .I have problem regarding fuel flow.after 30 mint of flight fuel flow showing 23 at 2000 RPM ,normal range is 10 to 12 GPH.at idle RPM fuel flow 12 GPH .I have FT 60 sensor..after landing and Cut off the engine .I start again at ground but problem was same.any one please help me...
  4. A

    Problem to read out dynon export data

    Hello,every one Please help me .I download data from my a/c through dynon USB.but I can't read out on my PC.because when I open its demand password.and I did not know any password.and more over the data is in zip folder
  5. A

    Backup ADHRS shows failure

    Ok but this problem is only solved with update and force load.remove ADAHRS plug and reinstalled it after cleaning.and compare both ADAHRS.and check enable button.i think the problem is only with software
  6. A

    Backup ADHRS shows failure

    Please update your software or perform force load option .
  7. A

    AMP Meter RED X

    Please replaced the fuse.and check ammeter connection on shunt.maxium this problem solved with fuse
  8. A

    Directional gyro

    Please performe compass calibration
  9. A

    No ammeter display

    Please replaced fuse maximum this problem solved with fuse .and check ammeter connection on shunt
  10. A

    MAP sensor and fuel flow and other engine instrument

    Hi.i am using dynon since 2016 .I am little bitt confused .if I remove the plug of fuel pressure sensor,oil pressure sensor,oil temperature sensor its showing cross on EMS screen or page,but if I remove the connection of RPM sensor or fuel flow sensor its not showing any cross why,and If I...
  11. A

    Battery voltage flikring at idle RPM

    Hi dynon..I am using 28 volt alternator and 24 volt battery.this was not happens before.at idle RPM which is 850 to 950 battery voltage flikring 21 volt to 24 volt.i replace battery and alternator but problem is still there.this problem only happened in flight and not repeat on ground
  12. A

    Warning light on EMS

    Hi.this is not a problem but I want to know about warning light located on EMS page.i am using EMS 220...last night My Aircraft Fuel light came on on EMS page only but anlog light was off wihch is located on another pannel ...I am using LM7812ct voltage regulator which convert 24 volt DC to...
  13. A

    Oil temperature sensor

    Hi.my oil temperature sensor is not reading correctly .my 35 minutes of ground runup check it's not going to green range which is 120 F .I replace the sensor but problem is same they are stuck at 70 F.plesea help me.and tell me torque value of oil temperature sensor
  14. A

    MAG pickup sensor

    Please help me for the installation of MAG pick up sensor.how to installed it.
  15. A

    Heated Pitot Status Does Not Work - Shorted to Ground

    Thanks dynon
  16. A

    Heated Pitot Status Does Not Work - Shorted to Ground

    Any one tell me how I installed pitot heater controller
  17. A

    Fuel quantity indicator

  18. A

    Fuel quantity indicator

    Total fuel or remaining fuel fluctuating only
  19. A

    Fuel quantity indicator

    Only fuel remaining problem rest all thing is correct I mean both tank showing correct reading
  20. A

    Fuel quantity indicator

    Please helpe please
Top