Search results

It also might think you're on the move if GPS lock were iffy, which can cause it to walk a bit and cause some of the behaviors to treat you like you're in-flight (where you definitely don't want a countdown)

Yes, you can only use one of 32/34 and 33/35. The pulses per revolution are set in SETUP MENU > HARDWARE CALIBRATION > EMS CALIBRATION > TACHOMETER CALIBRATION, and you can set both sets of pins individually (whether you're doing a conventional setup or splitting the L/R pins) . See the...

As more of a "power user" feature, this doesn't fall into our normal setup menu system. If you want to monitor two RPMs, load the file attached to this post. Then, you'll be able to select the RPM inputs separately from within your pin mapping setup.

Yes, if you have a voltage output that is below 10V, pins 32/33 won't be able to see it. Instead, used either of pins 34 or 35 (it doesn't matter which).

Yes, that's basically what people do. Set up a contact input on an otherwised-unused pin. Hook up to a momentary switch, and then use the state change that happens when it's open vs closed.

Our dealer in the UK - Mendelssohn Pilot Supplies , www.gps.co.uk - has technical support for our products. Or you can get in touch with our support team directly at 425-402-0433 or support at dynonavionics dot com.

An update here: Our updated shear screw design is shipping now, but we haven't made any big announcements yet. If you've had past issues with shear screws breaking (particularly more than once) do fill out a request at http://www.dynonavionics.com/shearscrew. If you haven't had issues with...

An update here: Our updated shear screw design is shipping now, but we haven't made any big announcements yet. If you've had past issues with shear screws breaking (particularly more than once) do fill out a request at http://www.dynonavionics.com/shearscrew. If you haven't had issues with...

Thanks for the reminder. They're shipping now, but we haven't made any big announcements yet. If you've had an issue with breakage, do fill out a request at http://www.dynonavionics.com/shearscrew. (if you haven't had issues with broken shear screws and yours isn't broken now, no need to replace...

Perhaps, but that's odd. Have you seen any "system event" alerts?

Not intentionally, but we'll try to figure out how the generation of the PDFs changed.

The TACs have more detail and info than the normal sectional, so I think what you're seeing is the place where those are "stitched in" by Seattle Avionics in the more zoomed in levels where there's a TAC available.

That sounds like a hardware problem. Logs won't be able to show us anything further here. When you say "fading in", do you mean that the screen was gradually getting brighter?

We don't comment on future product plans, so we're not able to give you any guidance here. But we're thrilled that you want to see more of our products in type certificated aircraft - we do too!

So the yellow and blue wires should measure a variable resistance. With power off, here are the rough numbers: 20C: 12.5K 30C: 8K 40C: 5K ...so your current reading of off-scale low could be the result of the probe just not being connected (wiring issue) You should also see 10K between the...

So definitely check the wiring. Since it sounds like this was an intermittent issue that got worse, that's where we'd look first. Check both for pins that aren't fully seated in their connectors, as well as broken wires. Beyond that, get in touch with our support staff at 425-402-0433 or...

So it sounds like there are two issues here. First, on the KLN - it sounds like SkyView isn't seeing a complete enough set of ARINC labels for SkyView to solely utilized it as a position source. If you disable the -2020 in serial setup, what does and doesn't work on the map/etc? Are there...

Also, make sure that your pitot line is going to the correct port (it's the middle one). If your other IAS indicator is working, I'd also be looking at a kink or blockage in the plumbing. If you get to the point that you're removing the pneumatic connections, you can simply take your finger...

It doesn't, but it's probably best to following their RV-12 specific instructions and packages for software updates, which are at https://www.vansaircraft.com/public/downloads.htm. Other than the software updates, you're really only updating the aviation/obstacles database routinely, which is...

So historically these turned on physical lights in panels, so those wires are basically just switched to ground. When the marker beacon receiver wants to tell you about a beacon, it grounds that wire to turn on a light (or ground it repeatedly to flash it possibly). So on the HS34, if that line...