Search results

There have been a couple of designs over the years. Our pitot, even with the vent ports covered up, will not fully seal by design. From the AOA installation guide: Note that the amount of leakage is not enough to change readings, but it may require that you connect upstream of the pitot to...

The only thing this should change is the word CHT to CLNT. Did you do anything custom with your pin mapping nomenclature? It does not inherently change the ranges - you'll need to adjust them yourself.

We are engaging a small group of customers to perform some radio testing and analysis with. We are particularly looking for the following: Customers that have had trouble with transmit and/or receive performance with SV-COM-425 (legacy Dynon radio). If you are one of those customers, you may...

There isn't a 6th serial port on SkyView (there might be something very deeply internal in the electronics, but there's no other secret set of pins that can be broken out). If there was a way, we'd definitively expose it. We know some customers are up against the 5 port limit.

The 30 seconds that HDX takes to power down uses a very small amount of the battery charge - in my own airplane I don't think about it. It doesn't have any bearing on the battery test or health. It's really a convenience feature that gives you some time to opt to keep the displays on after power...

It depends. If you're using SkyView's internal flight planning, and the waypoint causing a turn is set to not overfly (which is the default), then it calculates when a standard-rate turn would need to start to meet the next leg, based on your current GPS speed. This isn't adjustable. If...

Correct. All user/pilot settings and calibrations are stored in the displays, not the modules.

Only once. this procedure demonstrates what low AOA looks like to the calibration routine.

SkyView's HSI will point in whatever direction you have the CRS set to. The CDI will be correct per the localizer, but you need to have the HSI set in the right direction. Simple case: your localizer is 360. You have it tuned and you're right of course (needle to the left). If you have SkyView's...

Please start by reaching out to our support team before sending a datalog. Not all problems require that data, and they are time-intensive to decompile and sort through.

1) Not positive on this, but I think the auto-switch only work with devices that have both the NAV and GPS in the same device. IE, GTN/GNS/IFD type devices that have the nav radio option. Or, the SL30 may need to be configured with the GPS 172 so it's aware of it (not sure if that's possible or...

They're on pins 27/28 and 36/37 on the D37. If you select them in the pin mapping, you'll be able to select J/K thermocouples for those pins, in addition to the ones on the D24...

A few things: The terrain data doesn't update with any of the routine database updates. It's solely tied to the 4gb files here. https://dynonavionics.com/basemap-terrain-data.php. You'll notice they haven't been updated in a decade, because Terrain doesn't really change. Well admittedly, if Mt...

Sounds like you have everything installed correctly. You might measure the resistance on the resistor. It's included as you say, so it should be right.

Our next software update (likely dropping in 1-2 weeks) will actually change the priority to prefer ADS-B over TIS-B now that TIS-B is slowly being decommisioned and ADS-B is fully online.

Although SkyView does not support XM weather, most US customers equip with the SV-ADSB-472 receiver, which receives a variety of ADS-B FIS-B weather products, including nexrad radar, metars/tafs, lightning, and more.

There's nothing in the recent upgrade (even when it had the problem referenced above, since fixed) that should've broken tach that we know of. If you've experienced something along those lines, please reach out to our support team (link in signature)

We do have a replacement available now, for what it's worth.

As a old timer here that used to support the D10/D100 series back in the day, hobbs counts when oil pressure is alive (above some threshold), and tach is ratiometric to the RPM. Does the timer/clock work? That's another piece (that would only affect hobbs, I think, technically. So I can't think...

In general, Dynon Certified software updates are a mix of bug fixes and smaller feature improvements. We generally recommend running the most up to date software, but of course there is no firm time requirement or recommendation. If there WERE something that required a more urgent update, we'd...