Search results

Trying to understand my electrical system better (I had it professionally done and helped), but can someone in simple airline pilot/dummy language explain what the Shunt in the Skyview HDX system does and is for? I know it's not a fuse or a CB, we've got it wired Low off the + master solenoid...

Hi, I have a HDX1100. Wiring was done by Approach Faststack (attached). When I attach a USB drive to update the databases it does not recognize the USB input, but it does when I attach it to the back of the Skyview, so the USB is fine but the Skyview is not recognizing the USB extension. I had...

Min distance between the ADSB and Transponder antennas? Thanks

Maybe I missed it, but I see Left Fuel tank qty and right, but I only have a single tank in the fuselage. Did I miss that, or can I change it from Left to just Fuel tank? TIA

The 914 shows the MAP being taken from the Connector tube, which is pretty ittybitty. I then have to run it to the Dynon MAP Sensor, which is 1/4", a lot bigger. The Dynon manual says you might have to step down from the Dynon in/output to the specific engine, is this what you all have done? TIA

Sold

Hello, Rotax recommends I install a fuel pressure sensor in my 914 install, they sold me a UMA N1EU07D pressure sender. Not sure how to hook it into the SV-EMS-220. Anyone here done it? Thanks

Just checking, but if I read it right I only need to run AOA and Pitot fromthe Dynon pitot tube, ja? Installing on a SeaRey. TIA

Hi all, I'm doing a hybrid digital/analog panel, my Skyview will primarily be used as a MFD instead of a PFD, and I'll be using an analog airspeed and altimeter for that data. Any idea where I could find appropriate fittings for them to use with the standard Dynon pitot-static tubing? Looks...

Kinda boxed myself into a corner here, the best (almost only) way to route the wires to the warning lights is up the back of the Skyview, this is a temporary look-see mockup. I forgot the panel hangs from the top of the "arch" and takes up about 1" with cutouts for the 3 wire lights on the right...

Hey all, Since I'm doing a non-standard Skyview installation I'm in need of extra t-fittings, the manual recommends Coastal Pneumatics, here's the location if anyone else needs them: https://www.coastpneumatics.com/product-category/connectors/air-fittings/ Thanks

To use an ACI Gear Alert in my SeaRey I have to run a line/tap into the pitot feed line, the Gear Alert (https://flyingsafer.com/2080) is the black box mounted vertically behind the ADAHRS, and the simplest thing would be to tap off it as shown. Any problems with it being this close? Yes, it...

The 2 red wires from the Skyview SV-1000T go to a common circuit with a 5A cb, correct?TIA

Just curious, I've got a 261 transponder that uses a TNC connector, while the ADSB and Garmin GTR-200 radio uses BNC connectors. Is there a reason/convention they're that way, and the transponder does not use a BNC? Thanks

Anyone tried this with a Skyview Classic? Building a composite SeaRey and it would fit nicely in the nose by the transponder. http://www.advancedaircraft.com/ Thanks

Building a Progressive Aerodyne SeaRey, just wanted to challenge the "We always do it this way" thinking and am looking for alternative locations for the Transponder/ADSB antennas. Instead of running the wires all the way out to separate wings, I was thinking about putting them inside the...

Hi all, I'll be using my 10" D1000 as more of an MFD and have an analog airspeed and altimeter as my primary instruments in the center of the panel. Any thoughts about how/where to tap them into the green/blue/clear lines? Thanks

Hi gang, Really like the size and style of those connectors, I'd like ot use them on a couple other non-Dynon pieces of equipment in my build, anyone know where I can get them, or are they a proprietary Dynon design? Thanks

HI all, I found some LEDs I want to use in my plane, https://www.oznium.com/led-bolts-prewired-leds/led-bolt but they're just too dang bright. For various reasons I don't want to use a dimmer switch, is it Ok to put a small resistor (~1/2W, 560 Ohm) on the ground side of the LED, or will that...

Is it possible to: -Change the opening splash screen to one of my own creation? -Change the colors of the display? Thanks