Search results

Thank you. Looking forward to the upgrade.

I plan to update my original Skyview 10" Dispaly with a Skyview HDX 10" display. I want to make sure that all current settings/configuration is moved to the new HDX display. What do i need to do to make sure that I am able to get all the setting/configuration moved to the new HDX display...

OK. Just strange that the button had been working for years and the problem started as soon as I added the AP controller. But easy enough to disconnect it at the DB37 connector. Thank you...

Yes, I left the separate level button hooked up as well as the AP controller.

I recently installed the SkyView Autopilot Control Panel. Installation went well. It was discovered and code/FW loaded. I still have the Autopilot setting as Simplify and not Expert. The problem that I am having is that every once in a while I get a message that the Level Button is Stuck. In...

I can tell you that supply chain issues continues. All industries that use certain electronic components are dealing with this issue. I had a long wait for 2 of my 3 HDX, but I did get them with the 3rd one coming in last week or the week before.

Thank you

GKC Aviation. Can you provide me with the pin numbers and names on the COM 2 Transceiver Block and make them in reference to the SV-COM-T25? I am getting a little confused with the naming/function of each pin based on the documentation that I have. Thank you... Alex

Appreciate the quick response. I will be back at this in a week and go recheck my wiring. Thank you...

I installed the SV-COM-T25 Transceiver with the SV-COM-PANEL as my second COM radio through a Garmin GMA 340. The transmit is working great, but the receive comes in too low. In order for me to hear the receive, I have to bring the volume all the way up on the SV-COM-PANEL and it is still too...

Appreciate the update. Thank you.

Since we are now in the middle of March, any new news on when the experimental HDX will start shipping again?

Appreciate the feedback and now understand the status messages are from ADS-B IN. Will do a few more flights and pull the ADS-B Performance Report (PAPR). Plus I am thinking of removing the uAvionix echo and just replacing it with SV-ADSB-472. This way I just have a total Dynon Skyview...

Here are my Transponder Settings: STATUS ON-LINE HW22.03 FW01.02 SW02.11 USA $91.227 COMPLIANT YES TRANSPONDER WARNING NONE GPS DATA (OK) GARMIN ADS-B/ADS-B+ PRESSURE ALTITUDE (OK) SKYVIEW TRANSPONDER HEX CODE...

I just have the SV-XPNDR-261 and just wanted to make sure that my ADS-B Out is working. Will need to check the 430W for settings. I do have a uAvionix echo that I was using for ADS-B In and Out, but removed my Garmin 327 transponder and added the SV-XPNDR-261 and only using the uAvionix echo...

I just checked 7-34 and 7-28 in the User's Guide. While flying I do see TIS OK and TIS NOT AVAILABLE, but have not seen ADS-B OK or ADS-B No RADAR. Do these messages just pop up or is there a label that needs to be set up? Thank you...

Question/Help. I installed the SV-XPNDR-261 in my RV-6A. I have an original 10" Dynon Skyview Display. I am getting my GPS signal to the SV-XPNDR-261 from the Garmin GNS 430W. The Transponder menu shows compliance = YES. On my first flight I was told that other airplanes with ADS-B In were...

When set up correctly, I noticed that it works correctly. When the switch is on, it indicates that pitot heat is on and when the switch is off, it indicates that pitot heat is off. Never checked to see if as the actual pitot temperature changes if the indicators turns off and on. Dynon should...

Thank you.

I am trying to order a couple of AutoPilot Servo Shear Screws from Dynon or the Shear Screw kit part number 102991-000, but there seems no way to order the screws. I tried removing the shear screw and broke the head of the screw. How can I order the shear screw from Dynon? Thank you...