Search results

I am also very interested in one. Can be reached at 530 - five four 4 - 77 tree tree. Michael Z.

I have the HSI source set to the 430. It is showing the deviation on the CDI but not the vertical deviation sent from the 430 test screen. Thx, Michael Z.

I have a Skyview 10" classic and Garmin 430 non Waas. During the test screen on the 430, the Skyview HSI displays the CDI offset from center. But, there is no glideslope indication. I've had the 429 wiring tested and confirmed that I didn't fat finger the pin numbers. The 430 just returned from...

Does anyone have the data format for the Dynon ADS-B receiver ? I believe it is an "enhanced" GDL90 format, but cannot find any documentation. I want to send ADS-B data to multiple devices. I'm thinking of connecting an ESP-32 micro controller and writing a program to convert the data to...

Thanks I am just starting taxi testing after condition inspection this weekend. It's been a long road. I'm doing without the lights right now and using the Skyview EMS indications and warnings. I may add the lights connected to micro-controller (Esp32) later.

How do you setup Skyview to send and receive information with an Avare table ? I would like to , Send flight plans created on the tablet to Skyview Recieve Ads-B info (weather and traffic) from Skyview I have added my Wi-Fi adapter to Skyview and configured it; added airplane info and...

Did you ever get this corrected and how ?

I will switch the ground to the switch 😁 and retest. Also just recieved my new micro switches. Will try a quick test with one of them.

Ok this is what I did ..... not sure what fixed it. Connected the old EI head to the FT-60 and confirmed the transducer was working . Depinned 14,15 and 30 from the EMS module and tested pins 14 pwr , 30 grnd for power. With the battery charger on, I go 13+v. Checked the pins for looseness or...

I am testing the canopy wiring and setup before installing. I have a microswitch attached to pin 22. It is sending 12 v to the pin when the switch is open. To the same switch output I have a small warning light, recieving the 12v. The light is grounded seperatly. In the Dynon setup I have pin 22...

I am getting the same issue on my Garmin 430 non-WASS. However the HSI is recieveing the GPS signal. I have not been able to test VOR or ILS. Verry interested in your resolution.

Well, it finally stopped snowing or raining. I was able to connect the old EI fuel flow gage to the fuel transducer. When I was running the engine, the flow was about 3.5 ga/hr. I reduced power and mixture to see the flow change to 2.x ga/hr. So, the fuel transducer is working. The problem must...

Sorry for the delay, It's been snowing all week. The temp makes it difficult to work in the hangar. I did directly connect the Red and Black wire from the fuel flow to the battery. I still got Zero on the fuel flow display. That would lead one to assume it is the fuel flow sensor. But this...

Had Zero volts on the red wire at the Cube. The wire tones out fine but found only 8.x volts comming into the Ems box from the network. Traced 8 volts back to the 10" screen on the Dsub. Checked the voltage comming into the 10" screen and have 12.45 from the battery. There seems to be a voltage...

I have an EI Ft-60 fuel flow transducer. It was installed before the Dynon was installed and ran fine. I have wired it per the manual rev AE on page 7-57. Black - pin 30 White - pin 14 Red - pin 15 The wires ring out just fine. I have configure the Dynon Ems mapping to fuel flow and set the...

Well, as flying season approaches, I decided to make my life easy and replaced my Fuel, Oil pressure and Oil temp. Everything looks to be working and I'm anticipating first engine start in 2 weeks. Thank you all for your comments.

I'm updating my aircraft with a full Dynon suite. I've been running EI engine instruments for years and they have been bullet proof. But, I don't have room for both the EI instruments and the Dynon screen, (two place tandum aircraft). So, I'm trying to reuse the EI sensors. I've found out that...

Finally got this worked out. Seems there were multiple issues. 1. After testing the G430 com, I left the PTT wires temporarily connected to the HOTAS stick. They were connected with knife connectors. These were touching each other, ie. grounding. 2. When stripping the outer sheething from the...

PS Engineering 5000EX Installation Guide

That's exactly what I need. Thanks !!