Search results

  1. 1

    Does anyone know what fault this image shows?

    How can there be two vfr pilots on this forum, I wouldn't have thought this could happen. vfr pilot
  2. 1

    Charging iPad

    Ok thanks
  3. 1

    Charging iPad

    How many amps dose the 5V excitation circuit (ems pin 18) on my D180 put out? Is it possible to power my ipad on this circuit?
  4. 1

    What kind of airplane are you flying?

    Zenith Zodiac XL with D180
  5. 1

    Software update

    My D180 and AP74 are all new but bought at different times and will have different versions of software installed so I need to update everything to 5.6.1 (I have never done this before) After I have down loaded the support program to my laptop do I need an internet connection to upload to the...
  6. 1

    GPS DATA FROM GRT MINI X TO D120/D100

    Thanks for posting this Bob, I am actually thinking of doing exactly the same thing, swapping my Aera 500 for a Mini X coupled to my D180. Please keep us posted on what eventuates with this. Cheers VFR
  7. 1

    Auto pilot compatibility

    Is the GPS in a Grand Rapids Mini X compatible with my D180 auto pilot ?
  8. 1

    Display Voltage / Amps on D-180 Main Page

    It may be possible to configure a general purpose input from an HS34 to read volts and place it on the EMS page.
  9. 1

    VNav

    Will the HSI on my D180 display VNav from my Aera 500 ?
  10. 1

    AP74 and ipad

    In Australia the Garmin map updates are over the top with the exchane rate. Is there an app for the ipad that the auto pilot can run off. VFR
  11. 1

    Belite fuel sensors

    Thanks Jake
  12. 1

    Belite fuel sensors

    Will my D180 fuel computer work with the belite fuel level sensors.
  13. 1

    Oil pressure Sensor

    I have a Jabiru 3300 with the standard oil pressure sensor supplied with the engine. I'm wiring this into a D180, do I use the wiring instructions for Jabiru and Rotax on page 3-6 in the installation manual to do this. If so, will a 220 ohm 0.5W resistor be ok to use instead of the 200 ohm...
  14. 1

    Kavlico Pressure Sensor

    I have the Kavilco fuel pressure sensor that came in the Jabiru 3300 EMS kit and can't find the instructions for wiring it to my D180. If I remember correctly the red wire is 5V, the green is pin 8 on DB37 and black goes to ground, is this correct?
  15. 1

    AP74 Lights up

    I have the AP74,D180 and servos all connected up including the CWS button. I realise that the AP74 and the D180 both have different firmware but when i power up the system all the lights on the AP74 light up and the autopilot dose not register on the D180. Is it ok to have the AP74 on like this...
  16. 1

    Capacitive fuel probe "load"

    I have the same setup with resistance fuel senders but you cant run both analog and Dynon at the same time. I have them wired to a switch so if the Dynon should go off line for any reason I can flick the switch to the analog gauges and keep track of the fuel.
  17. 1

    Use of backup gauges with same sensorsor ll input

    I have a red cube for the fuel flow, I love the fuel computer in the FlightDEK, I just thought if it went off line for some reason I could flick a switch and the analog fuel gauges would come alive. I like to know how much fuel I have left thats all. Good point about human factors though.
  18. 1

    Use of backup gauges with same sensorsor ll input

    I plan on using analog fuel level gauges as well as my D180 but with a switch so I can switch from one to the other as I want. Will that be ok ?
  19. 1

    EMS Contact Function

    Thanks for clearing that up for me Murray, I understand it now.
Top