Search results

  1. R

    question for Dynon about autopilots moving forward

    sad but true
  2. R

    Shielded or twisted wire for yaw and pitch servos and where to ground the servos

    Vans specifically refers to Dynon servos in several instruction manuals i.e. OP 58-14
  3. R

    Shielded or twisted wire for yaw and pitch servos and where to ground the servos

    Thx a lot! If I would choose the shielded wires for the servos, where should I ground the shield? At the servo, at the front grounding point, both?
  4. R

    Shielded or twisted wire for yaw and pitch servos and where to ground the servos

    I'm installing yaw and pitch servos in RV10. Vans specifies shielded wire for data connection to the servos. Dynon's installation manual (figure 140) shows twisted pair(s). Q: is there any practical reason to use a shielded wire there? Another Q: Would it be OK to ground locally the servos or is...
  5. R

    Dynon intercom for 4 place aircraft

    Thanks! Thank you!
  6. R

    Dynon intercom for 4 place aircraft

    I did have a look at the MGL audio panel. It has all the bells and whistles which I don't want and don't need. That's why I'm looking for a solution to adapt the Dynon intercom
  7. R

    Dynon intercom for 4 place aircraft

    I’ve been using the Dynon intercom for a couple of years now and really like its simplicity and low panel foot print. As I’m presently building a 4 seater I was wondering if there is any hack or extension that would allow me to plug into the intercom 3 passenger headsets in place of the single...
  8. R

    Any alternatives to GHA15 radar altimeter?

    Are there any alternatives to the GHA15 radar altimeter, I mean a proper Radar altimeter not Lidar based device?
  9. R

    SYSEVENT 20 , HDX went black

    just a thought: shouldn't Dynon built the wifi interface into the HDX? How much more would that cost?
  10. R

    Version 16.7 software released

    @Dynon does it mean that the ACM no longer requires a dedicated COM port and communicates via the SV network?
  11. R

    VOR compass rose rings disappeared from map

    I've noticed that VOR compass rose rings disappeared from the Dynon map. I'm running the latest firmware on HDX. Anybody experiencing similar problem? Is there a menu setting that I could use to get the rings back?
  12. R

    AOA calibration warning

    same problem over here
  13. R

    Dynon Checklist Editor

    nice! :cool: thanks
  14. R

    "caution message" : knob panel off line

    It looks like withe the latest 16.6 version we got a trustworthy AOA indicator but lost the knob panel It's a fair deal ;)
  15. R

    "caution message" : knob panel off line

    from time to time my knob panel doesn't wake up, similar message on the screen I would re cycle the master switch and re boot the HDXs, that solves the problem
  16. R

    firmware 16.6.0 thank you Dynon

    Thank you @Dynon for the improvements in AOA indicator introduced in 16.6.0 Please keep up the good work and bring the AOA functionality up to the "on the speed" standard
  17. R

    how to add an additional temp sensor?

    Shorai LFX18A1-BS12, it's a very robust Li-FePO4 battery. Cell balancing is done using an external charger
  18. R

    how to add an additional temp sensor?

    Thanks for all comments. My battery doesn't have a BMS. I'm very aware of pros and cons, as well as operational limitations. There are two corner conditions that I want to monitor: low tem and high temp. Meaning respectively 40 and 170 deg. I'm OK with attaching the sensor to battery case.
  19. R

    how to add an additional temp sensor?

    Just to clarify, I'm NOT using an earthx battery. All I need is a temp sensor which could be attached to the battery box in front of firewall.
  20. R

    how to add an additional temp sensor?

    My battery doesn’t have a temp sensor I need to get one and connect it to EMS
Top