Search results

The aircraft is on the ground in the hangar. I was concerned about doing some damage with it beating itself up trying to go hard over after pressing Level or 180 buttons so I abandoned things until discussed on here. Any suggesttions what I might try and check? I will re-do Autotrim config as...

Hi, I have a couple of issues with my Skyview Autopilot/ Autopilot button panel installation which although I have read through the installation guides I can't get to the bottom of. Can you help please: Servos and Autopilot panel showing 'status ready' in config. Servo's calibrated=sucessful...

I guess so but you can't stop progress and if the demand is there .....

I guess the issue is the lack of GDL90 protocol in Skyview. Any chance of GDL90 protocol format being supported in future Skyview software upgrades Dynon? :) Those of us in UK/Europe don't need to comply with FAA 2020 rules that may apply in the US so pinBuddy would be a great addition for us...

I have EasyVFR 3.93, and Skyview 15.0.4. I use one of two x Ipad mini2's whichever I have at hand at the time. Now I wonder if this is the issue because on checking one has 10.0.2 and the other one has 10.1.1. I thought I had the latest iOS versions on both but obviously not. I will update...

I flew today and it hung still showing 'Waiting for Skyview' for 4 minutes (timed). Going out to Map and back in again made no difference or at least didn't seem to. It may have been me doing this,I don't know that finally activated it but it unfortunately to my eyes made no difference at all. :-/

I have two D1000's both with wifi dongles. In the wifi setup menu it shows Wifi-Online. In other word nothing amiss. The Ipad with Pfms/EasyVFR shows 'Waiting for Skyview'. Settings on the ipad mini show that it has found the Skyview wifi. At this point it just doesn't send to Skyview....so you...

Bump..

Not quite correct as I understand it. All you can do with Skydemon is transfer a Flightplan to the Skyview. No Skydemon data or anything else is available. I have talked and talked with the Skydemon guys about this to no avail. :(

Hi, Unsure if this an Pocket EasyVFR issue, a Dynon SkyView issue, or even an iOS issue but recently I have noticed that it takes a long time after loading a Flightplan for the button on the page to go from 'Waiting for SkyView' to 'Send F/Plan to SkyView. It used to be almost instantly and now...

Since I updated to 15.0.4. I have notice that when I turn off the P2 D1000 I get just momentarily ADHARS fail and EMS fail red crosses on the P1 screen. It does this on shut down and also if I do the same P2 screen turn off in flight. It is only momentarily and reverts to correct operation...

Well a sucessful update of my twin D1000's system was finally achieved with the help of you all. Just to tell you I tried an alternative stick and initially I got the same result,'Upgrade System Software' grayed out....I was not amused at this point!...However remembering what kellym said I...

Thanks for all the tips and advice guys. Much appreciated. I have tried putting the stick in both before and after powering the Dynon with same result....Update is still 'Grayed out'. I will try again with a different stick. I now have downloaded the firmware update to this alternative...

Hi, Thanks for the thoughts. I have tried both displays with the same result. I will try using another stick. I have an update lead from each of the displays which works ok for Mapping updates, are you saying that I shouldn't use this for Dynon updates?...Getting directly to each display is...

Help needed please... I have attempted today to update my twin D1000 Skyviews. This will be the first update I have done since installation earlier this year. Currently they show 12.2.0.2950. When I go into Setup>System Software>Upgrade System Software, Upgrade System Software is 'grayed out'...

I had a similar situation last week. (Pocketfms EasyVFR on Ipad).Normally F/plan transfer is instant and I never have any problem transfering a F/plan. However I had to power down for another reason and then after re start when trying to transfer F/plan from Ipad to Skyview I got a message...

No I have no visible alerts when I hear the sound. I will need check up on how to export user data logs and check the alert log. Unsure how to do that without reading up on it.

Well I tried switching off the Skyview that has the backup battery connected to it......still got the 'whoop, whoop'. Tried turning the transponder off....still got the 'whoop, whoop'. Not all the time I might add, just occasionally. I am now thinking of 'ground loop' from the ground wires which...

Ok thanks for the train of thought.An avionics guy has also suggested transponder. If I can pinpoint it I can then work on a solution afterwards. The thing that gets me though is I didn't have this until I connected up the Skyview audio!

No strobes was my first thought when this happened but with them turned off I still got it. The strange thing is I did two one hour flights on Wednesday and I didn't get the 'whoop, whoop' at all..not even once and I haven't changed anything at all! As I said previously it is so intermittent...