Search results

I have two physical servos in my airplane. The servo that is physically in the roll system is not being detected by the config system. The servo that is physically in the pitch system is identified and designated as "roll" servo in the calibration process. This leads me to the conclusion that...

The Dynon website says the Base map is 2013-06-20 but my installed version says 2014-09-04. Do I just be happy and shut up, or do I wonder why my version appears to be more current than the web site? My Stadium TFR db is 2014-09-04. How do I tell if that is current? Do I assume my Hi-Res...

Setting up dual 10" Touch SkyView displays. Also have Garmin GTN625. GPS 2020 antenna and Garmin GA35 antenna. I'm getting good satellites in both. I don't understand all the setup. I have Serial Port 5 as GPS-2020 in POS1. How do I set up the Garmin GPS as the IFR input source? The Garmin...

I have the installation manual revision AD in print, black and white, and refer to it fairly often. I have AF on the computer. 1. Is there any way to print only the change pages for AE and AF so as to update my printed manual? 2. I pay a local print shop to print in black and white because...

I see in an archived thread a request for pinouts of the SV-MAG-236 and a staff response that they are not published because they are connected through network cables. I need the pinouts. I am upgrading and have a severe challenge running new wire to the 236. I have two twisted pair running...

I'm finally installing new dual SkyView 10" Classic Touch that have been lying around for several years. I'm looking for feedback on the usefulness of adding SV-AP-KNOB and SV-AP-PANEL as opposed to simply using the SkyView knobs and menus. I will be flying cross-country, and I will be...

I tried to search on the acronym DRX but was told it was too short. Please code an exception so a unique Dynon product with a unique name can be searched. If I'd doing something wrong, I'd be happy to learn to search correctly on DRX. Thanks.

The book says to try to get the ADAHRS within 1° of level on each of the three axes and to do the same with the MAG-236. I can handle the ADHRS but the MAG is stuck in a carbon fiber wing and extremely awkward to access and manipulate. No way can I get a level in there. How do I know it...

May I assume there will be no GPS epoch issues with Dynon GPS devices and systems?

I see you offer a manual download and a redline version of the manual. I suppose if I looked at the redline version I could answer my own question, but does Dynon offer an update version of the manual? I ask because I have printed out the manual and if I could print only the updates I 'd...

Has anyone any experience or knowledge of installing the Dynon heated pitot in a carbon fiber wing?

I am upgrading my D100/120 system to D1000 in my Flight Design CTSW. I am deciding where to mount the ADAHRS 200/201 dual stack. I am using the mounting boss in the left wing for the MAG 236. How do I know the MAG 236 is 0° in all axes and how to I make sure the ADAHRS is congruent with the...

I understand that one point on the network is essentially the same as any other point.  That is, networking through modules such as going in one Com25, out it to another Com25, out it to a D1000 is the same as if all were connected to a hub. My question is whether there are any likely failure...

I'm upgrading my D100/D120 to SkyView D1000. I have a magnetometer in the wing and wonder if the old magnetometer will work well with the SkyView or if I should upgrade it?

My servo is going to be installed at a 45 degree angle.  The arm will be straight up (45 degrees to the body, of course).  Is there a specific set of holes on the body and bracket that will line up to 45 degrees to the body (0 degrees to the arm) and set the bracket for 100 degrees range of arm...

The servo would mount most easily if I can put the body at an angle to line up with a diagonal brace, but I want to run the lever straight up so it is parallel to the tab on the aileron torque tube. Any problem with installing the servo body on an angle and the lever straight up? Any problems...

I can't find the 2 pin connector that goes on the end of the wire from the SV-OAT-340 to the ADAHRS or Remote Magnetometer. Can someone give me a source and part number, please? TIA

Where can one learn about or discuss forum navigation? Specifically, is there a way to show all new posts when signing on? Most boards offer that feature. I haven't discovered it on this site. I couldn't find any other way to ask this question so feel free to move it or respond privately...

I am going to install the SV-MAG 236 in between ribs 5 and 6 in the right wing of a RANS S7-S. It is remote from ferrous metal and magnetic disturbances. 1. May I install the OAT in near proximity to the SV-MAG 236? By that I mean within a couple of inches? 2. The SV-MAG 236 product...

For airplanes with more than one EGT but not an EGT for each cylinder, can one ID them? E.g., the Rotax 912 I fly has an EGT on #2 and #3. Instead of L and R I'd like to name the 2 and 3. Can I do that?