Search results

sounds like you have a strong noise source interfering with your radios. It could be internal or external to your aircraft. Any high current machines operating nearby?

Here is a link to Avidyne software update. Yes, I installed it and it works fine. No problems with it. IFD 5XX/4XX Software Update 10.2.4.1 Update & Instructional Video For Loading - Avidyne Dealer Support Improvements include: · Reduced nuisance datalink alerts · Add password...

The most current IFD software is 10.2.4.1. I was able to download the service bulletin and software on the Avidyne web site.

You will have to connect your ELT to an unused serial port on SKYVIEW and configure that port to NMEA at the desired baud rate. I have this setup with the ACK ELT. • Configure the SkyView display serial port: SETUP MENU > SYSTEM SETUP > SERIAL PORT SETUP > SERIAL PORT x SETUP SERIAL IN DEVICE...

I loaded V16 and am somewhat disappointed there are no improvements supporting Avidyne IFD products. Since Dynon does not make a IFR navigator they are at a disadvantage to G. G products are much more able to share weather, traffic, ADS-B, radio tuning,etc. between their IFR navigator display...

I suspect you may have the logging periodicity set to slow, and the temperature spike was in between samples at a very short duration. You can set this in the skyview setup menu. "SkyView can record data as frequently as 16 times per second or as infrequently as once every 10 seconds...

So, you are seeing 279 C (535 F) for cyl temps? If so, that is way too high. You have a problem if this is real. The 350 F looks nominal for cruise. 400 F for climb. The DYNON system is normally very accurate. Your engine will not last long if those are real. Need to see more time to and...

I do not believe Skyview is able to talk to the VHF Comm section of the IFD XXX.

Here is an white paper on using GPS to Determine Pitot-Static Errors. It was written by Greg Lewis at the NTPS in Mojave, CA. If you go to their web site they have a free Excel download to do the math. This method has been used and written about many times in this forum and others.

I borrowed one of the PS engineering units from my avionics shop when my Garmin GMA340 was in the shop. I lost the AoA warning tones with this audio panel. I spoke to PS engineering at OSH and he said all the inputs on this have a squelch setting. It sounded like it needed to be adjusted in...

I am not that familiar with the GTN, but the IFD's can be configured as a remote device on the SkyView WiFi network. You can then retrieve a flight plan from your navigator into Foreflight, then push it to SkyView. This process is not perfected yet as Foreflight has some difficulty when more...

In Seattle Blog it says " Lifetime subscribers to FlyQ EFB will continue to enjoy great value from the ongoing use of our current products. Lifetime subscribers are our most valuable champions and going forward we will keep that in mind as we develop roadmaps for future products and features."...

If you are installing the Transzorbs and Fuses to protect your EMS module the components should be wired as shown below. The 18Volt Transzorb acts as a switch to ground if teh voltage goes to +18Volts. This will immediately blow the fuse protecting the EMS module. This is for a 14 Volt...

There is a program called DATPLOT available free on the web. I have used this and it works good. I have used it to measure takeoff distance in high elevation takeoffs. Kurt

yes

Dynon, I am trying to understand how you come up with the calibration coefficients. It looks like you are using more data than a Skyview user has available to generate the coefficients. Example: The new 150 PSIG (P255-150G-E4A) pressure transducer you have in the .SFG file the calibration...

Black Box data is the relative high sample rate data; whereas, the User data is the lower speed version. the Black Box data is about 15 mins of data at 16 samples per second (sps). Used for troubleshooting a momentary issue if you save it off within 15 mins of occurrence.. The User Data is...

Another note: for manifold pressure restrictor. I had used a brass screw in fitting on my Lycoming # 3 cyl.. Before installation, using a propane torch I filled the fitting with plumbers solder. Then drilled a #60 hole through the solder. This allowed the pressure change to be seen and...

MAP needs to be absolute pressure. Gage pressure is for oil and fuel pressure. The physical construction of Absolute pressure sensor has a vacuum on the other side of the diaphragm. Gage pressure the diaphragm is vented to outside static pressure. If you want to use the Kalvico P4055 series...

Pulses. The k-factor is the number of pulses it takes to count 1 gallon.