Search results

How long does it take for the Skyview system to completely initialize after you added power? Just curious for the times you go out to the hanger and just want to check how much fuel is on board Thanks

I am doing a remodel of my avionics system. It previously had a single Skyview and some antique Garmin avionics equipment. I am adding a second Skyview and removing all of the antique Garmin stuff and adding a Garmin GTN-650 and the Dynon comm radio Dynon autopilot, Dynon transponder, and...

derstand that the AOA system watches the two pitot tube ports and when the AOA tube port becomes more and more exposed to the airstream it will corolate that indicated pressure to the pressure that was seen during the calibration flights and indicate a stall. The question I have is how does...

I am getting close to first start up of a dual Dynon SV-1000 and a GTN-650. Since I will be flying IFR only in the US can someone please give me some advice on what Databases I need? Where do I get them? What is the most economical source? THANKS for the answers to the newbie...

How does one (me) mount the unit to the bottom of the wing of a composite airplane? I plan on installing it under the pilot side wing outboard of the strake fuel bulkhead of a Velocity XL. I see Dynon offers a Vans RV mounting kit that includes an aluminum “mast base” that the AN 5812 pitot...

Hi All, I have dual plasma lightspeed III ignition systems and I am trying to figure out how to wire them into the dynon EMS. Is there an advantage to wiring both ignition systems to the dynon EMS? If so what advantage will I get? I have two wires, each coming out of the lightspeed pin 6...

I need to wire up a K Type thermocouple on pins 36 and 37. My thermocouple has a red and black wire so I assume that the... -Red wire should go to pin 37 (what Dynon specifies as a General Purpose TC Input 2-) and the -Black wire should go to pin 36 (what Dynon specifies as a General Purpose...

Is a thermocouple polarized? In other words does it matter what wire goes to what pin the EMS module? THANKS

I've read 7-60 of the Installation Manual however I still am unsure of the answer so IF you can PLEASE help I would greatly appreciate it. I have a Velocity RG and I want the SV to display two green round circles when the gear is down and locked and two hollow circle when the gear is other than...

Hi All, I have read on another post of this forum that somebody was able to display the digital ignition output of a Lightspeed plasma 3 ignition systems. If this is indeed possible and somebody has done it would you be so kind as to walk me through the wiring and The Wizard setup procedure...

Hi All, How far should the ADAHRS unit be installed away from the heated pitot tube? I assume that the heated probe element causes some kind of magnetic field when energized so there should be a minimum distance. Alternately, how far from the ADAHRS can the pitot tube be installed? I ask...

I am building a composite pusher airplane and due to the rather large size of the ADAHRS and/or MAG-236 box size it is it difficult to find a suitable location. In the nose I have a landing light and an electric trim motor. In the tail I have an engine with electronic ignition. T the most...

Page 4-9 Power Input SkyView displays have a primary power input that is compatible with 12 volt and 24 volt systems (10 to 30 volts DC). There are two unterminated solid red primary power input wires (to reduce current loading in each wire-these are not for redundancy and both must be...

I am starting a different thread for this specific topic (I still need the other thread's questions answered). I think careful thought must be given to the feed source of the Dynon remote dimmer...perhaps everyone has been down this road but it is new to me. Pin 25 needs to see a regular, old...

I am trying to integrate a single dimmer knob to control the brightness of both my 8 RockRack switch indicator LEDs and the Dynon Skyview display brightness.  I am planning to utilize pin 26 as the Pulse Width Modulation (PWM) ground for my RockRack switch indicator LEDs as I understand the...

Hi All, I am looking for an app to use for flight planning and flight tracking while enroute. The ideal app would allow me to plan my flight at home (get weather/NOTAMS/file?etc) and then bring it to the airplane and zap it into the SV. I have a Garmin GTN-650 and SV-1000. I have used...

Hi all, Here is a product suggestion that I believe will make the Dynon Skyview product even better. !!!If enough users on this forum reply back and say they think it's a good idea, I'm sure Dynon will implemented this idea faster!!! So specifically, Skyview has a widget that can be set up...

Hi All, Great experience shared on this forum!!! I noticed on another post that the RV airplanes have external fans that are wired to the AUX fuel pump. What is the purpose of these fans? I am planning on a panel with dual SV-1000 plus SV autopilot /transponder /radio. The only additional...

I do not have sufficient pins left over for my temperature monitoring needs. One of the items I do not need to monitor on a regular basis is the turbocharger intercooler outlet temperature (the actual temperature of the air entering the engine inlet) as I just really need to see that on a very...

Can Pins 36 and 37 be used for a K type thermocouple (the manual says "general purpose TC")? If so...I assume that the red wire from the K type thermocoupler need to got the the pin 36 and the black wire to pin 37??!?!? I wish to use this K type TC to read engine inlet temperature downstream...