Search results

Excellent - thanks!

Well, if I type "curl --version" at the command line, it gives me the version info, so it looks like it :-).

Any chance of having a script that doesn't require downloading development software (WGET and all the things required to make that work) to use? I have a dead stock 15" Macbook Pro from Early 2013 running Catalina (10.15.7). Tried to install WGET and fell down that rabbit hole - gave up...

I would venture a guess that the volume control you're looking for is in your PS Engineering Audio Panel (you don't say which one you have). You'd need to know which input is being used to feed audio from the HDX to the AP, and then adjust the audio in the panel. Just a guess.

Yes. Any play or hysteresis in a feedback system can cause oscillations. To the extent possible, removing play and hysteresis is a good thing.

There's nothing in the v15 install manual about audio terrain alerts that I could find, and my HDX system doesn't give them (and I certainly don't recall turning them off during setup). The Garmin G3X, however, DOES do audio terrain alerts, and it's annoying as hell, given that I live in...

Bud, go here: http://www.aeroelectric.com/ and read Bob's stuff. The Book is available as a PDF here: http://www.aeroelectric.com/Catalog/pub/pub.html but I also recommend spending the $$$ to get the paper version, if for no other reason than to support Bob. In the book, Bob has a bunch of...

You cannot go wrong choosing the Nuckolls architecture (Z drawing) that fits your mission profile.

In Simplified mode, it seems so, yes. In Expert mode, you can turn on "Alt. Hold" only - don't need to turn on both - without turning on any roll related control. Or vice versa - turn on track without alt. hold, etc.

It sure as heck sounds like it, and now that I know what I'm looking for, there it is in the Pilot's Users Guide. Thanks a million - I knew I had seen it somewhere!

I thought I tried that to see if it would move with the map, but I don't recall that it did. I'll have to try it again. But if I want the map knob on the left when the map is FULL screen, then what? It seems to always have it on the right... Like I said, I thought I saw somewhere that you could...

So I may be hallucinating, but I swore that I saw somewhere (rev. 15.4.7, IIRC) that I could swap the knob functions so that the MAP knob would be on the left and the BARO/etc. knob would be on the right. I've searched the Menu, Display, and Setup screens, as well as scoured the Installation...

You explicitly said "The Autopilot has the default settings" which implies that you didn't "tune" anything during the tuning process. Some of the parameters will help with maintaining track without oscillating back and forth (I assume just a few degrees).

What's your definition of "wallow", and it sounds like you haven't gone through the Autopilot Tuning Procedure yet...

I have essentially the same thing (slightly modified Nuckolls Z-14, IIRC) in my COZY MKIV - two HDX's, two ADAHRS, no backup batteries since I have dual buses and dual alternators with a cross-tie. I agree that what you have is WAY better than a plane with a single electrical bus and vacuum...

The OP stated that he had dual displays but a single ADAHRS. Failure analysis is complex, and what you're shooting for depends on the mission you have. The OP currently has no redundancy with respect to ADAHRS's. They could install an SV-ADAHRS-201 as a backup (and have a backup battery for each...

No loops. The wire just goes through the coil - that's it.

Well, dang - that was it. Turned off the machine, set it to USB 3.0, booted windows, and was able to get DataManager to see it and use it. Thanks a million!

So, either installed for the first time, or reinstalled, the Extension Pack as described above - it said it was successfully installed. Got out of VB, started it back up and started Windows, got this - still no 2.0 / 3.0 USB support: No Joy...

Thought I did, but I'll try again... Thanks.