Search results

Table 120 - SV-ARINC-429 D25F Connector, page 23-15 manual revision AF shows one. For my own part, I am not personally knowledgeable.

My understanding is that when there are two or more servos and they work you are correct. Mine is the case of where I have two servos but only one is identified in the config process, and it's the wrong one. Thus my suspicion that if SV sees only one servo it assumes it's a roll (wing-leveler)...

My original question is a simple one - how does SV designate the servo name. You can see by reading my OP that I did a system config and attempted calibration. I didn't include the information about how I tested the servo systems and eliminated all wiring issues (except in the undetected servo...

I have two physical servos in my airplane. The servo that is physically in the roll system is not being detected by the config system. The servo that is physically in the pitch system is identified and designated as "roll" servo in the calibration process. This leads me to the conclusion that...

With your hints and reviewing the manual I think I got the correct settings input today. Thanks again for the help.

That helps. I'll take the book to the plane and try to follow 12-8/9 settings and see how that goes.

The Dynon website says the Base map is 2013-06-20 but my installed version says 2014-09-04. Do I just be happy and shut up, or do I wonder why my version appears to be more current than the web site? My Stadium TFR db is 2014-09-04. How do I tell if that is current? Do I assume my Hi-Res...

Setting up dual 10" Touch SkyView displays. Also have Garmin GTN625. GPS 2020 antenna and Garmin GA35 antenna. I'm getting good satellites in both. I don't understand all the setup. I have Serial Port 5 as GPS-2020 in POS1. How do I set up the Garmin GPS as the IFR input source? The Garmin...

Flight Design USA sells a heated boom pitot tube that fits where the old one was. I bought one last year. I can get the part number for you later if you need it. You run 16 AWG wire to them not for the current but for the voltage drop. If I remember right, the tubing is 4mm. I don't...

Each cable has the minimum bend posted in their spec sheet.

Are the procedure charts really from 2019?

Thanks for the comments. I use both digital and paper, and generally prefer digital for searches and paper for studying an item in detail. I was wondering if the color was sufficiently useful to make it worthwhile and appreciate the observations. Apparently change filler pages are not...

I have the installation manual revision AD in print, black and white, and refer to it fairly often. I have AF on the computer. 1. Is there any way to print only the change pages for AE and AF so as to update my printed manual? 2. I pay a local print shop to print in black and white because...

The question is moot. I was able to pull a network cable. I was hoping to learn a little than that pairs 1 (pins 1 and 6) and 2 (pins 4 and 8) were signal pairs; I'd known that from reading the manual Revistion AF pages 23-2 to 23-4. I'd called Dynon twice and they were either unwilling or...

I see in an archived thread a request for pinouts of the SV-MAG-236 and a staff response that they are not published because they are connected through network cables. I need the pinouts. I am upgrading and have a severe challenge running new wire to the 236. I have two twisted pair running...

Thanks to everyone's helpful responses, I've decided to add both devices at my upcoming upgrade.

I'm finally installing new dual SkyView 10" Classic Touch that have been lying around for several years. I'm looking for feedback on the usefulness of adding SV-AP-KNOB and SV-AP-PANEL as opposed to simply using the SkyView knobs and menus. I will be flying cross-country, and I will be...

I bet SteinAir would make you one up if you gave them the connector specs. Any decent local amateur radio club would have peopled with the skills and tools to make one.

I'm not familiar with the AOA on the SkyView system, but used it extensively on the D100. In the D100, the aircraft I used was calibrated per Dynon instructions and the result was to stall at the last remaining red chevron. I take it then that Dynon changed the calibration procedure so the...

I tried to search on the acronym DRX but was told it was too short. Please code an exception so a unique Dynon product with a unique name can be searched. If I'd doing something wrong, I'd be happy to learn to search correctly on DRX. Thanks.