Search results

To be clear, load a High Resolution terrain database that includes Australia? SkyView displays as shipped (with some exceptions) have the North America High Resolution terrain database loaded.

How are you determining the brightness? This will help us understand if there is an issue and how to correct it.

Battery testing issues and the FAA report issues are both scheduled for a fix in v14.1, hopefully to be released soon (but no date certain yet).

When you're next in your aircraft, give Dynon Avionics Technical Support a call at 425-402-0433 (preferably on a day other than Monday; you're more likely to get straight through to a Support staffer rather than voice mail). They can walk you through some troubleshooting where you can push...

We're not familiar with this device. If it produces a pulse relating to RPM, generally yes, it's compatible with a SkyView SV-EMS-220. Recommend using the low-voltage RPM inputs, Pins 34 and 35.

1a. If you have an EFIS-D100 or EFIS-D10, you will need to connect directly to that instrument's "PC connector" to update it. This connection will also update the AP74 and servos (if installed, connected, and configured). 1b. If you have an EMS-D120 or EMS-D10, you will need to connect directly...

A shear screw being broken would cause the arm to move, but not the actual servo. Check that the castle nut on top of the arm is moving as well as the arm.

Brad, We replied over on VAF as well. It's a bit tricky to try and manage two identical threads at once as they diverge! http://www.vansairforce.com/community/showthread.php?t=135878 I think you'd do better with a call to us when you're at the plane and it's outside. We can see all sorts of...

And as a note, in v14 and later SkyView software, we automatically set this based on your N number for US registered aircraft so you no loner need to look it up.

You might want to check this Service Bulletin.

Tobi: Those P/Ns are not known to be compatible with Dynon Avionics EMS units, but they may work - you'll have to experiment. As another poster mentioned on another new installation, if you have the luxury of running new wires. recommend you run a ground, +5V (EMS 37-pin connector Pin 18), and...

Dynon Avionics units serial outputs and inputs are "real" RS-232 voltage levels.

You should see a pulldown option at the bottom of your screen, and you can select 40 most recent posts.

This sounds like you have the flap position indicator wired wrong and it's shorting out the power supply on the VP-X, which will cause other analog readings to drift. This will happen if you swap the signal wire and a power wire on a potentiometer. Does the flap signal move at all as you move...

Alain: All we can tell you from this message is that the panel unit cannot communicate with the SV-COM-T8. There is no additional troubleshooting that can be done. In our experience, this issue is usually a wiring mistake. If you've verified EVERY wire, every connection, every pin, then please...

We have heard your requests, but at this moment, we have nothing to announce.

Did you verify that the wires you connected go to the correct pins? Blue/White or Black - Pin 13? White - Pin 21? It's very common to have the wiring incorrect. The correct wiring is to connect the TX of the EFIS-D10A (Pin 13) to the RX of the transponder. Many confuse this and connect "TX to...

Dynon Avionics EMS units have two inputs ("Left" and "Right") for RPM / Tachometer. The EMS unit only displays ONE RPM / Tachometer. The one that is displayed is "the first input that was receiving pulses". If, at some point, such as a Mag check", no pulses are received on that input, then the...

Apologies for your confusion. Attempting to clarify, if you have an SV-GPS-2020, version of v14.0.x.xxxx firmware (or later) is required as the SV-GPS-2020 does not function in earlier versions of SkyView firmware.

Robert: If you install multiple ADAHRS, and also install the corresponding OAT probes, the SkyView System will choose one of the ADAHRS to be Primary, and display that unit's OAT. If you want to change which ADAHRS is Primary (and thus display that unit's OAT): SETUP MENU > PFD SETUP > ADAHRS...