Search results

I have a VAL NAV 2000 wired into my HDX display. When I cross over the outer and/or inner markers, should I be getting some indication on my display? Or do I need to install an additional light on the Panel hooked up to an output ssignal from the NAV2K or tHe HDX?

I ma experiencing pitch oscillations, i.e., the Altitude hold is not stable, Altitude oscillates up and down around the target altitude with magnitude of between 30 feet to 180 feet, with a period of about 35-45 seconds. In the Inflight Tuning process guide, the only thing I can find that seems...

Could the HDX system be modified so that ADS-B/TIS traffic, (and maybe weather as well), be displayed on top of approach plate and SIDs, just like on the main Map display? The system already shows moving own aircraft icon on the plate, so it can't be a major code redesign to do this. Currently...

I loaded the HDX data file from 15 JuLY, which was supposed to contain updated version of these files, but they have expired. Wassup?

Is there any way to calibrate the oil temperature sensor to make sure it is sending the right signal to the EMS? Also, I have been told that single wire oil temperature sensors (that use the engine crankcase as pathway to ground) are frequently unreliable due to ground loops and that two-wire...

I have been trying to reach Dynon support all day (at 425 402-0433) and the phone service at that number seems to be disconnected or out of service, or something... Has anyone else seen this?

I am suddenly getting this message intermittently. When it happens, and I run the Network configuration Detect function, it fails to find the AP-Panel. But if i shut down and restart the HDX, it finds it okay. I have checked that the connections are tight, and the pinouts on the network wires...

Should I use the same pinouts for the Garmin GPS175 db25 connector as are specified for the Garmin 430/530 in the SV-ARINC-429 Installation section of the Skyview Installation guide (Figure 156 on pg 12-6 through 12-8) ? (ignoring the VOR/ILS stuff)

Am I correct that a small amount of play in the connection between Pitch Servo pushrod and the pushrod it attaches to (between the Stick and the Elevator BellCrank) cause the Autopilot to oscillate up and down around the target altitude in Altitude Hold ?

Anyone have any experience with adding Screen protectors to the HDX screen? I am looking at product from Photodon... Dynon SkyView HDX 1100 10-inch Panel Display Screen Protector (photodon.com) Does it negatively impact touch functionality or anti-glare visibility or clarity at all?

When creating my own Skyview Network cable, I thought I should connect pin1 to pin1 , pin2 to pin2, etc., all the way to pin9 connected to pin9. But when you look at the end of the female DB-9 connectors on a network cable that shipped with my Dynon HDX system, and do a continuity check on them...

Today I had issue with Transmitter on Com Transceiver (SV-COM-C25 with SV-COM-425). Reception was fine on all frequencies, but I could hear no side tone when I pushed PTT button and spoke, and although ground control could hear me but said that my transmissions were weak and unreadable. When I...

What (if any) ELTs can accept external GPS data from the GPS-2020 ? How about the ACK E-04 406 MHZ ELT (Iavailable from Aircraftr Spruce for $611)? ACK E-04 406 MHZ ELT KIT WITH WHIP ANTENNA USA | Aircraft Spruce

Has there been any testing or compatibility work done between HDX wifi and IFlyGPS? Specifically, related to uploading flight plans, and/or downloading ADS/B data into tablet over wifi? I have been experiencing intermittent data transfer failures, (even when wifi shows successful connection)...

What does this mean? The servos staus show as ready, and they are working okay.

How accurate is the Cylinder Head Temperature readings output by the Skyview system? I have Lycoming O-320 E2D, with Dynon HDX, and all Dynon engine sensors installed. The CHT sensors are in the Lycoming standard CHT Sensor ports on the Intake manifold. I had a possible CHT over-temp the other...

Is the Garmin Sl-30 COM/VOR/ILS attached via a serial port to the Skyview HDX, (with SV-XPNDR-261 and SV-GPS-2020), constitute an "IFR Navigator" for the purposes of satisfying FAA IFR requirements?

With the obvious caveat that it's not done until it's done, it would be extremely useful to have some regular or intermittent updates on the release schedule for HDX version 16. Perhaps a short blurb on where you are in the software development cycle might be added as a thread on a discussion...

By default, bearing pointer 1 in the HDX points to the current GPS waypoint. You cannot control this. Many of us only have one nav source (an SV-GPS-2020/250), installed. In this case bearing pointer 2 is more or less useless. It would be a very useful enhancement to add functionality to allow...

What are advantages of installing a second GPS? I do not have a NAV radio. The Skyview HDX users guide (pg 4-19), says that you can connect the two bearing pointers on HSI to any one of the nav sources in the system, and the bearing pointer will "point" at the "radio station or waypoint". It...