Search results

Reloaded sensor file and upgraded to SV 15.0.4 and the problem has gone away, at least for now. Corrupted sensor file ????????? ;)

Lycoming O320-E3D engine in an RV-9A that has been flying and perform perfectly for almost two years before this happened. Perfect means that the amp meter shows the battery recovering from starting or the nominal system draw if the engine is not running and up till now the proper load...

Have a Skyview with the Dynon amp shunt. Amp indications reads perfect with engine off or at low power but as soon as the engine gets up to about 1600 or better RPM the amps jump to negative 30 or higher amps then the panel indicator goes red X. Indications flux off and on, mostly Xed,  after...

Checked both servos and see physical movement of the servo arms. What would cause the servo to not detect the movement and how can I check that.

Network shows both servos. Initial ground configurations says could not detect all servos. See attached screen pics. Both servos checked for mechanical connection.

Tried the initial SV servo calibration today and it fails saying it couldn't find one servo. Both the pitch and roll servo show up in the network but the calibration fails. How do I find out which servo it cant find?

Has there been a lot of defective backup batteries lately? I am on my second failed battery since last June. Batteries initially seems OK and passes test but then will slowly stop charging and finally die. Acts like one or more of the LI batteries quits taking a charge. Doesn't seem to act as...

FInished troubleshooting today. As improbable it might seem the EGT probe in question choose to die just as I did the install. No a V14 problem. :D

All my EGTs were working fine until now. I uploaded V14 and right near the end of the process I got a red flag and an error that went away before I could read it, Now EGT1 is red X. Checked all the connections. Should I try a new V14 upload?

What is the typical life span of the backup battery? I need to get the third battery in less than a year. First one died while building. Second one was fine untill I installed V13 and then it stopped charging even though it passed the backup test. Can't believe these shouldn't last longer that that!

Does the Dynon L shape unheated pitot tube have a drain hole. If so where do I find the little bugger. Trying to test for pitot leaks but cant maintain pressure at all.

Getting a red X on backup battery after installing v13 and Skyview claiming battery fail. Checked battery and ran battery test and it passed OK. Replaced battery with new one and get the same stuff. Worked great until I install V13. As Microsoft would say.. Its not a bug but a feature instead?

I have a Vans tach transducer installed. I see in another older post that it was believe to generate 1 Pulse per rotation. I am seeing about 4 times the real RPM with a single pulse per rotation (PPR) setting in my Skyview. Have you found a need to set the PPR higher, maybe 4, for the Vans...

Is there a spacing requirement for distance separating a Dynon GPS antenna (Puck) and a Garmin 430 GPS antenna?

Worked fine afer deleteing everything from the stick and downloading the two files to the stick again. ThanKs for the help Garrett.

I am getting a warning that my navigation database is out of date. I downloaded the av_data_FAA_5.0_1303.dup and ob_data_FAA_5.0_1302.dup files into the root of my USB stick. When I install the memory stick and go into the Skyview setup to load the files they don't appear on the list of files...

Is there a minimium distance between a Whelen strobe cable and ADAHS or AHARS DASB cable that must be observed?

Is there a minimium distancethat must be observed between strobe cable and servo or servo DASB cable.

Installed power correctly and found LED. You are right I do need better hangar kights.

The installation guide references a red LED on the unit. I don't actually seem to see one. Is thais a typo or do I need better lighting in my hangar? Pete