Search results

I have a D-180 (master), D-100, HS-34, AP-74, SL-30, GTX-327. Everything works great except when I put the 300 in the "hold" mode through the innunciator button to go into a holding pattern or missed approach, I have no ability to adjust the HSI course value with the HS-34(when the holding...

Poblem Solved!!! Found error in the wiring at a juction- gnd and TX2 lead switched. Scott

Re: Setup Procedures for Garmin 300, SL-30, GTX-32 Lan, I found the problem last night- two wires were in error- gnd and TX2 were switched at a junction splice. Thanks for all you effort and help on this. All the interfaces seem to be working with no issues. Thanks again, Scott

I do have the setting to #4 and Icarus. I have also switched back and forth between 10 and 100 resolution with no affect. I guess the next thing to try is to disconnect the EFIS Tx2 Gnd (Pin 21) from the ground block and see if that changes anything. Next, is to remove the EFIS connector and...

I have a D-180 and D-100 with the 180 being the master unit and a Garmin GTX-327 Transponder. The GTX-327 is not displaying altitude data from the Dynon. The settings are per the installation manuals and input from the Dynon forum. I am trying to figure out what the problem is. The shielded...

Re: Setup Procedures for Garmin 300, SL-30, GTX-32 Lan, I verified today that the GTX-327 settings were as you provided. They were already there but still no altitude input. As I look at your schematic, it shows the serial out connection from the HS-34 (which I assume is pin 13) and the...

Re: Setup Procedures for Garmin 300, SL-30, GTX-32 Lan, I haven't had a chance to try the config from your last email. I will go to the airport tomorrow morning and try it. I don't think I have it set to "4". I am glad to hear you are happy with it for IFR. That was the whole reason I went...

Re: Setup Procedures for Garmin 300, SL-30, GTX-32 Lan, I entered the values you provided tonight and they resulted in very good progress. The good news is that by entering the values you provided the GPS now finds satellites, the D-180 is receiving data from the GPS (magenta arrow in the HSI...

Re: Setup Procedures for Garmin 300, SL-30, GTX-32 Lan, Thank you very much for all you effort and time doing this for me. It is exactly the direction I have been trying to find. I will go to the airport tonight after work and put in all the settings and see what happens. As far as the...

Re: Setup Procedures for Garmin 300, SL-30, GTX-32 Lan, Thank you very much. One more thought.....since the altitude info is going from the Dynon to the 327 and from there to the 300, did you have any settings you had to do in the 327? Scott

Re: Setup Procedures for Garmin 300, SL-30, GTX-32 Lan, Thanks for your answer. I had Stark Avionics do my wire harness and it appears that they connected the Dynon altitude data to the GTX-327 and the 327 to the 300 just as you show in your schematic. If yours works, then mine should...

John, Do you by chance have all the settings written down for the SL-30 and GNC-300 and how you get into the menus to enter them in each instrument? I have a D-180, D-100, HS-34, and AP-74 plus the above two instruments and a GTX-327 transponder. I am trying to figure out all the settings to...

I have a D-180, D-100, HS-34, AP-74, GNS-300XL, SL-30, GTX-327. My wire harness between these the above was done by Stark Avionics per the Dynon wiring diagrams in the installation manuals. I am having trouble figuring out all the settings to get them to interface correctly. I can find bits...

Configuration being installed: D-180 (primary), D-100, HS-34, AP-74. Question: The wiring harnesses for the D-180 has two 9-pin connectors for PC interface (one EFIS and one EMS), the D-100 one connector, and the installation manual shows one required for the HS-34. Can you explain how these...

I am goin to use a D-180 (primary), D-100, Hs-34, and AP-74 (roll only) and am currently working on installing all the harnesses and related wiring. The D-180 has (1) DSAB connector on the 25-pin EFIS connector and (2) on the EIS connector. Are these (the EFIS and EIS sides) interchangable in...

I am installing a D-180 (primary), D-100, HS-34, and AP-74. For the serial 2 TX connection to the transponder (Garmin GTX-327), how do I handle connecting both the 180 and the 100? Do I just connect the 180 or both? If I only connect the 180, what do I do with the 100 sheilded lead- remove or...

I need some help. I am building an RV-7A and would like IFR capability. My plan is (was) to use a D-100, a D-180, a HS-34, a Garmin 300 XL GPS, a SL-30, and a GTX-327. I talked to tech support at Dynon and it sounded like things would mesh. However, I received a phone call from Stark...