Search results

  1. Stevec

    Switching L/R joysticks

    MAP MENU-MAP MODE-FULL SCREEN MAP allows you to set left or right knob when in full screen mode for the map.
  2. Stevec

    What's involved in adding a second Skyview?

    Vans supplies a standard loom for the RV12 which has all wiring and connectors for two screens. There is no need for hubs or anything else. If it’s the standard loom you just plug the screens in. lets not go down the track of overcomplicating everything until the OP has a look to see what he has...
  3. Stevec

    What's involved in adding a second Skyview?

    My advice is have a look behind the panel and see if there are connectors there for a second screen before getting too involved in what is required. oh yes i should have specified Ethernet cable in my previous post when I said network cable.
  4. Stevec

    What's involved in adding a second Skyview?

    With the RV12s I have been involved with using the standard supplied wiring loom the wiring is all in place for a second screen. I suspect all you will have to do is buy or make the instrument panel section with the appropriate cutout and then plug the new screen in. i don’t recall seeing the...
  5. Stevec

    Sensor File for Release 17.1

    The Aithre Shield EX has a sensor life of 10 years and has three connection wires. Power ground and sensor output. Sensor output can go to any spare input on the EMS but the enhanced sensor inputs are the best apparently. Good install instructions and quick response from Aithre to fine tune...
  6. Stevec

    Sensor File for Release 17.1

    I have just installed the Aithre, which is working great, and was advised by Dynon the the audio alarm you can expect is “ Engine Monitor” there is no Specific CO audio alarm built into the system.
  7. Stevec

    RV12 Flap Overspeed Alert - HDX setup

    Not sure you need the switch. I have installed a Ray Allen position sensor and programmed the flap positions through the calibration routine in hardware setup, I think that’s where it is. When the flap is out of the calibrated up position and speed exceeds the max flap speed I get the warning...
  8. Stevec

    Skyview system frozen/locked up

    Hi i I had exactly the same issue a while back. I sent the diagnostic file into Dynon and they found it was a memory error. The solution was to reboot and it all comes back to life and has been working fine since. The longer term fix is to send it in for memory replacement I believe. Apparently...
  9. Stevec

    Aithre C0 detector

    I have followed this question up with Dynon and using the sensor definition included with the latest HDX sensor file Skyview will give an “ Engine Monitor “ audio alert when the needle goes into the red.
  10. Stevec

    Aithre C0 detector

    Thanks for the replies. My question was do you get an audio alert. I know with some widgets that there is no associated audio alert on the Dynon system so that was the reason for my question. I think I was quite clear that it was the sensor I was choosing between, Aithre, Flight DataGd-40 and...
  11. Stevec

    Aithre C0 detector

    A question on the Aithre Shield EX 2.0 installation as I haven’t found the answer in any other posts. When the sensor is installed and set up with the supplied sensor file does the Skyview system give an audio alert when the needle goes into the red zone? Just trying to choose between the...
  12. Stevec

    Ownship Icon pointing wrong

    Check it with a hand compass. You will soon see if there is any major magnetic interference. My 6 does not have a remote mag I just use the one in the adhrs which is mounted behind the baggage bulkhead.
  13. Stevec

    Firmware update for autopilot

    If it’s not working perhaps an email to Dynon may help.
  14. Stevec

    Dynon Skyview interface board

    There is some confusion here. Both of my Skyview screens have a db37 connector on the back. The OP s board is a distribution board that takes one 37 pin connector and distributes it to two Skyview screens avoiding the need to splice wires together for the serial ports etc. It is not a network...
  15. Stevec

    Dynon Skyview interface board

    Not quite sure how a 25 pin hub will work with a Skyview system that used a DB37 37 pin main connector.
  16. Stevec

    A/P initial setup

    Think you might need to configure the network if all is as it should be electrically. Go to Setup/system setup/Skyview network setup and carry out a network configuration. This will go and look for all the devices attached to the network. As far as I am aware the network is not plug and play.
  17. Stevec

    Auto pilot panel causing trim failure TECHNICAL SERVICE BULLETIN: 104808-000

    Not sure what aircraft type you have but Vans released a Service Bulletin about this last year.
  18. Stevec

    Circuit breakers

    I leave the autopilot power turned on all the time so I guess that will reduce the chance of an internal breakage. I have never flown an aircraft yet where you have to completely power off the autopilot for any particular phase of flight. I am happy to follow Dynons advice , installation manual...
  19. Stevec

    Circuit breakers

    I have used a Tyco W31 switch circuit breaker which combines both functions. Seems to do the job ok.
  20. Stevec

    Vertical guidance

    Revision aj the section I posted was cut from that page. No mention of traffic or ADSB.
Top