Search results

Attached is a copy of the Dynon Intercom Installation and User's Guide. It has diagrams showing all the electrical connections for reference (pages 2-3, 2-4). Andre'

"I could tell you, but then I'd have to kill you."

Absolutely sounds safer. Is there a manufacturer guideline or someone else's POH matching your plane that you can reference for their stall figures? That would at least get you in the ball park for your stall numbers. Don't forget you should be doing these stall calibrations at a high altitude...

Adding flaps alters a wing's camber, changing the shape of the wing and increases the AoA: https://www.boldmethod.com/blog/2013/10/how-does-lowering-flaps-affect-angle-of-attack/

I heard an interesting debate that calibrating the AoA with no flaps might give the pilot better warning when performing maneuvers, such as circling tightly over a point, alerting the pilot before a sudden "moose stall" occurs and might be least expected. The flipside being as Carl mentioned, in...

What is a "full" calibration? I spoke to David at Dynon Tech support this week and he told me these 2 rules for calibrating the AoA system: 1) Every time you perform and SAVE a stall calibration, it over writes and replaces what was in Skyview's memory. Performing more and more stalls and...

How do most pilots calibrate their Skyview AoA system - with no flaps, partial flaps or full flaps? I have an RV-6 with a new Skyview install and am ready to calibrate. If I calibrate using full flaps, wouldn't the visual & aural AoA indicators be skewed/offset when landing without any flaps or...

Correct. Any of the 5 ea. serial ports can be used with any serial device, as long as Skyview is configured properly (baud rates, type of data, (sentence structure, i.e NMEA) parity, etc.) and protocols for each device are set the same (Skyview <-> Garmin GPS). Also - the Skyview serial ports...

Yes, my message referenced vers. 16 of the Installation manual, the latest version released earlier this year. Click on the Installation Guides tab on the above link posted above by swatson999.

Yes, on pages 4-38 & 4-39 of the Skyview System Installation guide. There is a Dim Offset menu accessed by pressing the Display button (#7) from the Main Screen.

Have you tried raising the Minimum Brightness Sensor Value?

Enter System Setup Menu (press and hold Buttons 7 + 8) and navigate to Local Display Setup > Brightness Setup (see attached). There you will find the screen brightness settings. Andre'

And you will get it back with repairs made and the knowledge of what failed. How old is the Skyview system?

Have you checked your Skyview's back-up battery? Try performing a self-test under load and check the results.

Attached is Dynon's Skyview Data Communication diagram I found helpful while wiring/connecting.

Awesome. Page 11-3 of the same Installation Guide confirms the mounting tray dimensions used on the SV-COM-T25 & the SV-XPNDR-261 are identical. Thank you!

Perfect. Do you know where I can find a real-size/full scale drawing of the mounting tray used on the SV-COM-T25? If I had that, I could begin configuring my sub-panel while I wait for the transceiver to arrive. Is it the same tray used for the SV-XPNDER-261?

Thank you for posting this. It does confirm the X25 is superior to the C25, being a digital transceiver vs. analog. Although I'm a bit unsure the X25 will solve my noisy reception issues due to the sentence "This transceiver generally has very good reception performance, but sometimes had poor...

You had issues with your transmissions (Tx-talk) or reception (Rx-listen)? I hear no complaints from others while transmitting, only when I'm receiving. Interesting Dynon had you add an additional ground wire from the SV-INTECOM-2S to the SV-COM-425, as there are already many grounds connecting...

Thanks Marc - I didn't realize the SV-COM-T25 was the Trig replacement Dynon was sending me. After reading your post, I do see the differences outlined in the installation manual. Looks like I am not done with my Skyview installation!