Search results

I just purchased a Sandisk Cruzer Fit 128GB drive for Seattle Avionics charts. I am able to access the charts on this drive without a problem. However, with that drive installed I cannot see anything on the 32GB Sandisk Ultra drive that I have been using for a year or more - notably I could...

The Skyview can only read the drive if it's formatted in FAT32. Page 3-18 from the current Installation manual. You can check that from File Explorer. Craig

Did you follow the prep instructions on Dynons web site? Is the drive formatted in FAT32? Craig

To confirm, if I want a secondary display for ONLY EMS, I need to hook up every serial device parallel to both displays? Craig

I am planning to swap my GTX327 for the SV261. My last 411/413 was a year ago so I have a year left compliant. As I interpret 91.413 swapping out the transponder requires the 91.413. The two questions are has anyone done this w/o the full 91.411 (can it be done) and I am correct that no error...

Since there are two distinct models I assume it is not possible to convert a /H to a /V or vice versa. I have roomm for a /H now but will likely do another panel refresh in a couple of years and would then prefer a /V. Craig

Ah hah! Thanks for the clarification, I need to read the installation manual more closely. :-) Craig

Hi Dynon, What is sent to the 250/2020 that requires use of the TX side of the serial port? This thwarts my plans to share that port with another device at the same speed. Regards, Craig

Fair enough. I hoped that maybe my info was out of date. :-) Thanks for the candid and prompt response! Craig

Question on the last sentence. I seem to recall that the Skyview would NOT provide vertical guidance on the HSI unlike an external portable such as my 496.

The key difference in using the 335 - or any other Mode S transponder versus the SV-261 is that you need to provide the GPS input directly to the transponder per Dynon's documentation. If you are using the SV-261 you can use one of the Skyview serial ports for the GPS input. The 335 will wake...

I guess those emails did the trick!  Foreflight 7.0.1 enables Connect with Skyview in the basic subscription. :-) Craig

I'm with you. The Wifi dongle is CHEAP and I was IN until I read that I need to give Foreflight another $75/yr for the privilege. I consider my Skyview as my primary nav display and the iPad with Stratus 2 as a backup so if I wanted the FF Pro features I'd pay Seattle Avionics $99/yr to have...

Disregard. Did some more reading on the subject and answered my own questions. :)

Thanks for taking the time to respond Vern. If I'm reading your entry correctly it is dependent on 3 pins, is that correct? If so, what are the outputs from your EI that are mapped to those 3 pins? The Lightspeed only provides for a single output for Ignition Advance, MAP, and low voltage...

Hi All, Has anyone with a LS configured their Skyview to display the amount of ignition advance as output on pin 3 of the LS output connector? Any tips? Craig

Very exciting stuff! And the best part is that those of us with the existing version of Skyview continue to get major new features with a FREE software update. There are very few companies out there in ANY business that continue to add this level of value to existing customers without...

Sigh. The good news is that changing the EMS setting from 0-80 PSI to 0-30 PSI to match the transducer installed corrected the problem. (Dynon: I have the twin connector version of the transducer) The bad news is I have no explanation as to why it was wrong since I do not ever recall seeing...

Re: High indicated fuel pressure Thanks for the suggestion but as I indicated my Aux pump also indicates high w/o the engine running. I also just used a mechanical gauge and it reads 3-4 PSI. NO doubt now that it is an indication problem. Craig

Hi, Since replacing my engine driven fuel pump I am seeing fuel pressure readings of 13-14 PSI - versus the 4 PSI expected.  I connected a mechanical gauge to the line and it reads 3-4 PSI. I found an older 0-80 PSI transducer which indicates 4-5 PSI so it is definitely a issue with the...