Search results

Are the charts you plan approach plates, Sectionals, Low IFR,High IFR or some combination?

I have electric pitch trim with a position sensor routed to display on the D1000. This works just fine. The issue I have is that the widget to display this is designed to display 2 axis trim. I do not have roll trim. The current trim widget shows the pitch trim position but there is a large...

Dynon Support will be along shortly to confirm but I believe the units compare the pressures between the AOA and pitot ports and as such both are necessary.

Russ, Tech Support will probably be along shortly to confirm but up to now all software upgrades were cumulative such that if you loaded the latest, you had all previous changes without having to load any previous versions. I suspect this is the same.

Surely this doesn't mean you are not going to support 1948 Thiokol ST-147 Loran to ADF trans-interrogators does it? Rats! Oh the humanity!

Perhaps a menu item in the setup that places the unit in "Baro Test" mode or something could be done. The unit would then ignore these airspeed/altitude changes for purposes of system adjustments. I would suggest replacing the PFD with "TEST ONLY" and then the airspeed, altitude and vertical...

For those that are space constrained bear in mind that the Skyview display itself will flash a warning message based on the parameters you set. It is the same event that triggers the external master caution you wish to install. A master caution light would simply be an additional signal but I...

I would like to see this as well.

The first use I would plan for this capability would be a canopy alarm. My plane (like Mmarien) has canopies that will detach from the airframe and be lost while possibly damaging the tail surfaces if opened in flight. I suggested several triggers as possible in my original post. For my primary...

I confused GND with STBY. Thanks for the info.

One small point to remember if you fly to one of the 140 or so airports in the US that have scheduled air carrier service is that Auto will need to be temporarily disabled. These airports have surface movement tracking based on transponder returns (ASDE is the name of the system I believe)...

The Dynon GPS does not meet the requirements for stand alone navigation under IFR rules as it is not certified to do so. A navigation receiver must be certified to act in this capacity. Dynon explains this in the instructions. The Dynon may act as a navigation display to show the output of a...

I would second Steve W.'s suggestion to ask them. Bear in mind regulations written to require a "warning horn" on disengage were written long ago when everything was analog. There was no synthetic digital voice to tell you a specific event occurred. It is likely the voice will meet the...

Fair enough. That was part of my reluctance to ask. I too envisioned everyone wanting to tie any two (or more) parameters together. Any chance we might gain access to the trigger you use for the AOA alarms? Even I it were triggered at a low but repeatable airspeed below flight speed a chance to...

Is there a chance Dynon might have a conditional contact and/or alarm in the Skyview? The first example that jumps to mind is a contact which determines canopy closed/locked status. I can currently set a contact to monitor this but it would be a real bonus if this could be set to only alarm...

Really like this idea as well.

You have to press buttons 7 & 8 simultaneously to enter Setup. Once there navigate to the update menu. If you do not enter Setup the Skyview will not look at the system files on the drive. It is only expecting to use it for flight plans unless in Setup mode.

Dynon, is there a way to disable data storage or delete it? I am not interested in making this data available to anyone. I can live without it myself if that is what is necessary to remove this record keeping. Perhaps a choice in the setup would allow users to choose to activate the datalogging...

The easiest way to tell is a simple check. My D10A does the same thing but it is because the previous owner (who installed it) mounted the OAT probe in the NACA vent for the cabin air. Air leaking out of the engine cowling during flight goes right to the probe. The probe is very sensative. It...

If your static port does not stand proud of the surface and "trip" the air going past, there are often times errors in the static pressure. Small errors in static pressure can affect altitude and indicated airspeed. Both of these are used to compute TAS as shown above so an error is static...