Search results

That is what I thought, but as I stated in my reply, I do not think that all the data is actually loaded into your computer and ready to transfer to the USB key. Also make sure that you clear the cache. Once you clear the cache, you will need to start loading the data from the Airmate website...

I had this same issue. The cause was slow internet speed. I did an internet speed test and noticed that the speed was much slower than what I was paying for. Called Spectrum and told them that I suspected the cable modem to be causing slow speed downloads. They came to the house. Tested the...

Thank you...

Recently I have been getting a CPU TEMP HIGH message. I think I have also seen a CPU TEMP CRITICAL message. This unit has been working great for 13 years. Just started seeing these CPU TEMP issues now. Outside temperature was actually cool (60's) during today's flight when the CPU TEMP HIGH...

Just spoke to Dynon. They have the two diagnostic logs that I provided and they will be doing analysis on the data.

Yesterday the three SV-HDX1100 in my RV-10 rebooted during takeoff. Each time during takeoff and full throttle. On Sunday when I encountered the first SYS EVENT 3 it was during a Takeoff stall. I have sent the diagnostic logs to Dynon for the reboot this past Sunday, but no response yet. I...

Yesterday the reboots of the three HDX displays occurred 4 times. Each time during takeoff and full throttle. On Sunday when I encountered the first SYS EVENT 3 it was during a Takeoff stall. I have sent the diagnostic logs to Dynon, but no response yet. I also sent Dynon an email and no...

Today I was doing my second flight on my RV-10 with three SV_HDX_1100 that I recently completed. I was testing stalls and right before the takeoff stall occurred, the three HDX Displays rebooted. I know had no instruments. When the Displays came back up, the PFD had a "SYS EVENT 3: SEE SETUP...

Connect your FLAPS position signal to the VP-X Pro (J1 Pin 17). The TRIM position signals depends if you are installing a SV_AP_Panel. If you are installing an SV_AP_Panel, then connect the Elevator Position Trim (Pitch) to the SV_EMS D37 Pin 4 and you can connect the Roll Trim position signal...

I now have the FLAPS Position indicator working. I found an old posting from from Sep. 6, 2020 that states to remove the EMS FLAPS widget in the editor and then in the editor find a FLAPS selection. I found a selection FLAPS (1). I selected FLAPS Position (1) and now at the bottom of the HDX...

I did the calibration and the calibration worked. The flaps and trims move as calibrated and I can see the changes in value at the sensor debug for the flaps and the trims. I also have the widget on the screen, but the widget does not indication the position. I am sure that if I connect the...

I have an RV-10 with Dynon Skyview HDX and VP-X PRO. In the Dyon Skyview setup, I have FLAP Position, AILERON TRIM Position and ELEVATOR TRIM Position set to VP-X. In Dynon Skyview Sensor Data, I can see the position values for FLAPS and TRIM change as I move the FLAPS and TRIMS. The position...

Thank you. Looking forward to the upgrade.

I plan to update my original Skyview 10" Dispaly with a Skyview HDX 10" display. I want to make sure that all current settings/configuration is moved to the new HDX display. What do i need to do to make sure that I am able to get all the setting/configuration moved to the new HDX display...

OK. Just strange that the button had been working for years and the problem started as soon as I added the AP controller. But easy enough to disconnect it at the DB37 connector. Thank you...

Yes, I left the separate level button hooked up as well as the AP controller.

I recently installed the SkyView Autopilot Control Panel. Installation went well. It was discovered and code/FW loaded. I still have the Autopilot setting as Simplify and not Expert. The problem that I am having is that every once in a while I get a message that the Level Button is Stuck. In...

I can tell you that supply chain issues continues. All industries that use certain electronic components are dealing with this issue. I had a long wait for 2 of my 3 HDX, but I did get them with the 3rd one coming in last week or the week before.

Thank you

GKC Aviation. Can you provide me with the pin numbers and names on the COM 2 Transceiver Block and make them in reference to the SV-COM-T25? I am getting a little confused with the naming/function of each pin based on the documentation that I have. Thank you... Alex