Search results

OK, I went to my hanger to check. I had been running a two screen classic Dynon system with Ethernet cable and I had already established that it worked with either one or two screens powered. I disconnected the ethernet cable and powered up one screen all worked worked and I would see the EGT...

It seems strange that the Ethernet cable woudl be needed to transfer EMS information between the two units, I thought it was needed to trasnfer configuration data between the two units. I can test this in my system that has two Dynon Classis units probably later today. I will remove the cable...

Why would you be concerned about the battery in the 540 with regard to the default location display. Wouldn't the HDX get it location information from the Dynon 251 or 2020 GPS receiver?

Confused about the reply to my suggestion. In Revision AG of thee Installation manual on page 4-34 Dynon states: "If there is more than one display on a SkyView network, you MUST connect all displays’ audio outputs to the same audio panel input to ensure that audio is always heard. Electrically...

The wiring of a dual Skyview system to the audio system should connect the audio outputs of both Skyview systems together and then to the audio panel. This ensures that when one of the Skyview units fails that the other unit can still send an audio message to the audio panel

question: do you have a Skyview backup battery installed for both displays separately?

Could it be that if Dynon considers the aircraft is in flight then it will keep the display and reports the "Aircraft lost power" and when the aircraft is considered in rest and on the ground that Dynon presents the countdown and the option to power off now? So maybe the issue with with the...

Hello Rob, The Kavlico sensors are the ones to be used for Fuel and Oil pressure, not for the MP sensor. There is a completely different sensor to be used for the manifold pressure as this is a much lower pressure range

NO, The GPS-2020 is much more than just an antenna, it is the complete GPS receiver and the interface is just a power and serial rs-232 data interface, The GTN 650 has just an antenna in their puck.

I assume you have the seial connection from the SL-40 to the Dynon installed and are getting correct messages on the link status. Did you configure the interface for SL-40?

Most likely that will work, although it is not clear how the LED internal power limiter works from the data sheet. Experiment with different resistor values till you get a desired brightness level.

Hello Joe, For both the fuel level sensor and the trim and flap position sensors you should be able to measure the raw sensor signal when these are connected to the normal system and verify that the expected sense lines (the lines that eventually end up at the Dynon EMS) actually change levels...

So the 5 Volt supply for the potmeter is purely an Dynon EMS issue as this wants the returned position signal, that goes into the EMS be in the range from 0 to 5 volt

The motor (two white wires on the ray alan) runs from 12 Volt. But the sensing potmeter is supplied form the 5 Volt so that the return sense line retunes a variable voltage between 0 and 5 Volt for the position indication.

Thanks for the reply, that makes upgrading much easier. Changing the sensor configuration is not a big issue, but redoing wiring is much harder. With regard to using the single 150 psi for all the measurements above the 15 psi range. This comes at a price of reduced resolution, when you are only...

Thanks for this information. One general question regarding the suggested new Kavlico sensors. Do these new sensors have the identical interface (5V supply) and interface plugs (pinout) that connect the sensor to the aircraft harness and the Dynon EMS module? So are these basically plug in...

It's hard to respond without any additional information lime a main power diagram. With the main source you mean the main battery, but then how is your aircraft wired, isn't there a main power relay that shuts the complete power to all the aircraft systems off. What remains powered when your...

That is not right, the Dynon Skyview hub connects the Skyview networks together, and connects the display, EMS, ADHRS etc. all together but that is not an RS232 connection. The VAL serial connection goes to one of the five serial RS232 connections on the display,

Note that the Dynon "GPS antennae" are not just the antenna (like the Garmin 430 systems), but these are actually the complete GPS receivers. These pucks include the receiver circuitry and the digital electronics that lock up with the GSP signal. The data that is relayed to the displays (2 power...

I understand that there is no date available for this additional functionality to get information from the UL Power ECU. But is some information already available, like for instance what interface would be used to connect the UL Power ECU to the Dynon system. And maybe more important is this...