Search results

I think it is referring to the GNS430W firmware. The firmware has the protocol that supports Dynon XPDR at the correct SIL level. The database is for approaches and terrain on the 430W.

Dynon did email me back and said they are able to duplicate this problem and they were working on a fix. It is a bug in ver 15. Kurt

Diag file has been uploaded. I had the Pitot Static and Transponder checks performed this evening with the -201 set as primary to get around Pitot Static Test Mode limitation. I swapped it back to the -200 as Primary right before I downloaded the Diag file. Thanks, Kurt

I will get the diag file to you later today. In the normal COMPARE mode it works fine regardless of which ADAHRS is primary. Only the Pitot / Static Test Mode is affected. Thank You, Kurt

I checked the Network Configuration and it all looks good. I repeated the selection again for the Primary ADAHRS and got the same results. With the -200 as primary it will not see the -201 in the Pitot Static Test Mode. With the -201 as Primary the Pitot Static Test Mode see's both ADAHRS...

OK I got it working but think I found a bug? If I have the ADAHRS-200 selected as the Primary and the ADAHRS-201 selected as the Standby the Pitot Static Test Mode will not see the standby ADAHRS-201. So I selected the ADAHRS-201 as the Primary and it will now display both ADAHRS data. Does...

I know the network detects both ADAHRS. I don't remember the "COMPARE" option when I went to the ADAHRS selection page. Only the primary one as "ONLINE SELECTED" and the second displayed but "OFFLINE", I think. When I get back home ill check it out in more detail.

Dynon, I will be needing my IFR cert on my Pitot/Static this month so I thought I would try the new feature for this. "New: Pitot/Static test mode that elmiminates the need for display restarts during transponder checks. Available via SETUP MENU > HARDWARE CALIBRATION > ADAHRS CALIBRATION >...

I also have a Garmin 430W and will occasionally see the loss of data from the 430W for a brief second. I have seen this with pre-version 15, but not on version 15 yet. I just upgraded this week. But since the latest version of 14.xx. I still see the blinking out of data but not the A/P change...

Thank you! That makes sense. I will move my tach signals to the Hi V inputs... KR

No external zener installed.  There is one internal, 12V.  Direct wiring to the SV EMS.  I am surprised the SV has such a low input impedance.   I was expecting at least 1 M Ohm.  Before I dig into behind the panel to change to the High V inputs or build a Tach distribution amplifier would like...

Dynon, I am wondering what the input impedance is on the "Low Voltage" tach inputs on the SV-EMS. I have dual P-Mags with SV connected to the Tach signals which outputs 12 V signal. When I connect to the SV the Tach signal drops to ~5V. The P-Mag has an output pull up of 4.8K ohm to 12V...

V15 new feature. >"ADS-B Traffic and Weather from SkyView’s SV-ADSB-470 is now transmitted via Wi-Fi for use by 3rd party apps (FlyQ, Foreflight, etc)" Has anyone tried the Wi-Fi ADS-B link to Naviator (Android)? Thanks, Kurt N122KR - Glasair Super II RG, SV 1000T.

I also experienced the ghosting from Western Louisiana (Alexandria) into East Texas (Cedar Creek) yesterday afternoon. I saw myself as traffic about 1 mile north of my position and on a few occasions I saw other traffic was duplicated, looking like two aircraft in formation. Ill send a note to...

Dear Dynon I recently changed my TACH CRUISE RPM setting and once I landed and recorded my TACH time in my paper log I noticed the TACH TIME was incorrect, at a old setting. My question is: when entering the engine settings page is the CURRENT TACH TIME pre-loaded into the setting or is it the...

Dynon, I see with the HDX with version 15.0 the engine gauges can be displayed on the bottom, full width. Is this an option on the non-HDX models? ie. 10" touch. Thanks,

Dear Dynon, Yesterday during an IFR flight from Tampa, Fl. to Fort Worth, TX I noticed two traffic displays anomalies at different times. First, was "Displaced" labeled under the target. The second was a target's label toggling between "1200" and "VFR". Both of these occurred between FL...

Bob, Sorry I had an error in my calibration calculation. Should be y = 8.919080x - 1.783816 sensor={ id=MPX DIFF PRESSURE ;UN-VERIFIED function=PRESSURE pins=C37_P8 C37_P22 C37_P23 C37_P31 name=DIFF PR min_val=0 max_val=40 resolution=0...

Bob, For the MPX sensor you provided the calibration is y = 0.112119x + 0.200000 to give EU's output in "Inches or Water". So create a new sensor definition like: sensor={ id=MPX DIFF PRESSURE ;UN-VERIFIED function=PRESSURE pins=C37_P8 C37_P22 C37_P23 C37_P31...

Bob, This looks like it will work. It outputs ~0 to 5V, but it requires 5 volt excitation. So you will have to get that from some place. Needs to be mounted, designed for a Printed Circuit Board. Calibration is no problem. If your not planning on installing this permanently then there are...