Search results

You do not need the flight calibration. Ground calibration is acceptable. Is your Dynon using an GPS 250 antenna? The early ones had a software error that caused an incorrect magnetic variation table to be used after a certain date a few years ago. This affected heading and therefore winds...

Sadly, moving away from the GNS 480, everything is a compromise. Mine is paired with a Skyview in the Glasair Super IIS RG I just put up for sale. What a great combination! One night on a trip to the northeast I was given three full route clearances in the space of ten minutes all different from...

We tried for a long time to get Dynon to accept GDL90 data. When Dynnon was having so many problems in the development of the ADSB 472 they almost went ahead and allowed GDL90 data over serial to be read by Skyview. Unfortunately for us, they solved the ADSB 472 development issue and came out...

Contact Dynon Tech Support by phone. They will send you the kit. Leave the old screw in place. Each servo has the ability to have the shear screw in three places so each could tolerate a shear three times before having to go back to Dynon. That said, having a shear screw break more than once...

Sorry I could not add this text to the original post with the picture but it is just above. Look on the left edge of the Map to see the Flight Plan Source box which says Skyview. On the PFD note the two boxes to the right of the HSI. The larger one is labeled Skyview which is the HSI source. The...

There is a small semi clear rectangular box at the bottom right of the PFD screen. It will show the HSI source at the top. Below that will be the source for Bearing 1 and Bearing 2 if you enabled those. The autopilot follows whatever the HSI source shows in this box. There is a similar box on...

Try making sure your Map Source, Flight Plan Source and HSI Source are all set to the same navigation source you would like to use.

Check that the Dynon reads zero when parked. A Zero Airspeed Calibration is easy and will fix this if not.

If you are using the advanced autopilot you can simply go to AUTOPILOT>ROLL and you will see the active roll mode. If you had just turned on the autopilot it will be either HDG or TRK. Simply touch the highlighted mode button and it will disengage leaving altitude mode engaged. Your flight...

You really do not need to wire up your alternator light. Simply set the voltage and amperage ranges correctly on the respective widgets. If the alternator goes offline your Dynon will give a warning, flash the message and announce "Electrical Current" in your headset.

Happy to help!

Would love to see a serial port expander for the Dynon. Grand Rapids has this for their systems. Use one serial port to add three more.

I have the same Skyview/ADSB 472 and Echo UAT/ GRT Mini setup as you and very often have the same problem. It would be great to be able to adjust or disable the traffic filtering on the Skyview. Many times the Skyview does not show traffic which is shown on the GRT and Ipad from the Echo UAT.

The transponder is a serial device (not Skyview network) in the Dynon system. Check to make sure it is still shown on you Serial setup page. If it is there, look for Good Sentences counting up. Check to make sure transponder is powered.

Enter the Maintenance log in the Setup screen (location shown two posts up). You can edit, remove or add any of them. You will get more familiar with the location as you use the system as you must return to update the values as you might do after completing an oil change for example.

I have traffic from both a Dynon ADSB 472 displayed on the Skyview and from a Uavionics Echo ADSB tranceiver which displays on a GRT Mini and also an Ipad. You may have two issues. First is the Dynon filters traffic it does not consider a factor (too far above, below or distant). This filtering...

Unfortunately, the Dynon will not accept ADSB in from anything except their very expensive SV ADSB 472.

I have rolled my firmware back using the debug files. The procedure is actually quite simple. I can give you the details if you like.

You should try the Configure function. Go to SETUP MENU>SYSTEM SETUP>SKYVIEW NETWORK SETUP>CONFIGURE. This will find your EMS again. It should work normally when this is complete.